Bond strength of composite resin luting cements to fiber-reinforced composite root canal posts.

J Contemp Dent Pract. 2007;8(6):17-24

Authors: Le Bell-Rönnlöf AM, Lahdenperä M, Lassila LV, Vallittu PK

AIMS: The aim of this study was to compare the attachment of different composite resin luting cements to a fiber-reinforced composite (FRC) post with a semi-interpenetrating polymer network polymer matrix. METHODS AND MATERIALS: Six different brands of composite resin luting cement stubs were applied on the surface of FRC post material and light-cured for 40 seconds. Shear bond strengths of luting cement stubs were measured using a universal testing machine. RESULTS: The differences in shear bond strengths between the cements were not statistically significant. CONCLUSION: All of the tested composite resin luting cements provided acceptable attachment to the tested FRC post. The tested FRC post material is suitable to use with different composite resin luting cements.

PMID: 17846667 [PubMed - indexed for MEDLINE]

Degree of conversion of adhesive systems light-cured by LED and halogen light.

Braz Dent J. 2007;18(1):54-9

Authors: Arrais CA, Pontes FM, Santos LP, Leite ER, Giannini M

This study evaluated the effect of blue light emitting diode (LED) and quartz tungsten halogen (QTH) on the degree of conversion (DC) of an etch-and-rinse Single Bond adhesive system (SB) and a mixture composed of primer solution and resin bond from Clearfil SE Bond self-etching adhesive system (CB) using Fourier transform infrared analysis (FTIR). Adhesives were applied to potassium bromide pellet surfaces and FTIR analyses were performed before and after photo-activation for 10 s with either LED (Freelight 1 - 400 mw/cm(2)) or QTH (XL 3000 - 630 mw/cm(2)) light-curing units (n=8). Additional FTIR spectra were obtained from photo-activated samples stored in distilled water for 1 week. The DC was calculated by comparing the spectra obtained from adhesive resins before and after photo-activation. The results were analyzed by two-way split-plot ANOVA and Tukey's test (p<0.05). Both adhesive systems exhibited low DC (%) immediately after photo-activation (SB/QTH: 18.7 +/- 3.9; SB/LED: 13.5 +/- 3.3; CF/QTH: 13.6 +/- 1.9; CF/LED: 6.1 +/- 1.0). The DC of samples light-cured with LED was lower than DC of those light-cured with QTH, immediately after light curing and after 1 week (SB/QTH: 51.3 +/- 6.6; SB/LED: 50.3 +/- 4.8; CF/QTH: 56.5 +/- 2.9; CF/LED: 49.2 +/- 4.9). The LED curing unit used to photo-activate the adhesive resins promoted lower DC than the QTH curing unit both immediately after light curing and 1 week after storage in water.

PMID: 17639202 [PubMed - indexed for MEDLINE]

Dentin bond strength of composites with self-etching adhesives using LED curing lights.

J Contemp Dent Pract. 2007;8(5):34-42

Authors: Korkmaz Y, Attar N

AIM: The purpose of this study was to investigate the effect of light-emitting diode (LED) light curing units (LCUs) compared with halogen LCUs on the shear bond strength (SBS) of one nanofill composite (Filtek Supreme) and one microhibrid composite (Artemis) with self-etch adhesives. METHODS AND MATERIALS: The buccal surfaces of 60 non-carious extracted human molars were flattened to expose dentin and, subsequently, polished for 60 seconds with 600-grit wet silicon carbide abrasive paper. Specimens were assigned into six groups (n=10) according to composite material, self-etch adhesive, and curing light used as follows: Group 1: Adper Prompt L-Pop (AP) and Filtek Supreme (FS) using an Elipar Free Light (EFL); Group 2: AP and FS using an Elipar Free Light 2 (EFL2); Group 3: AP and FS using a Hilux Expert (HE) light, Group 4: AdheSE (AS)+Artemis (AR) using an EFL; Group 5: AS+AR using an EFL2; and Group 6: AS+AR using a HE light. The specimens were thermocycled for 500 cycles (5 masculineC-55 masculineC) and then loaded to failure in a Zwick universal testing machine at a crosshead speed of 5 mm/minute. SBS values were calculated as megapascals (MPa) and statistically analyzed using the one-way analysis of variance (ANOVA) test at a significance level of 0.05. RESULTS: Mean SBS (+/- standard deviations) values were as follows: Group1: 15.99+/-5.18; Group 2: 18.76+/-6.71; Group 3: 17.70+/-5.04; Group 4: 16.93+/-3.99; Group 5: 18.01+/-5.19, and Group 6: 17.46+/-5.40. There were no statistically significant differences for SBS to dentin among the groups tested. CONCLUSION: The LED curing lights used in the study seem to be comparable with the halogen curing light for nanofill and microhybrid composites used in conjunction with self-etching systems in dentin. The EFL2 reduces curing time, which can be considered as an advantage.

PMID: 17618328 [PubMed - indexed for MEDLINE]

Chlorhexidine's effect on sealing ability of composite restorations following Er:YAG laser cavity preparation.

J Contemp Dent Pract. 2007;8(5):26-33

Authors: Geraldo-Martins VR, Robles FR, Matos AB

AIM: The aim of this study was to evaluate the influence of chlorhexidine on microleakage of composite restorations in class V cavities prepared with a carbide bur (CB) and a erbium:yttrium-aluminum-garnet (Er:YAG) laser. METHODS AND MATERIALS: Cavity preparations were created on the buccal surfaces of 48 bovine incisors using different methods then equally dividing them into four groups. Groups I and II were prepared with a #56 CB in a high speed handpiece while Groups III and IV were prepared with a Er:YAG laser at 350m J/4Hz on enamel and at 80.24 J/cm2 on dentin. The cavity preparations were rinsed with 2% chlorhexidine solution before the application of Clearfill SE Bond system and placement of a Z100 composite resin restoration. After 24 hours, the teeth were polished, thermocycled, and sealed with cosmetic varnish. The samples were then immersed in 2% methylene blue for four hours and sectioned in the buccolingual direction to determine the degree of microleakage. RESULTS: After statistical analysis (Kruskal-Wallis, p<0.05), no significant differences were verified among the tested groups and between the evaluated cervical or incisal margins of the restoration. CONCLUSION: The use of the chlorhexidine did not interfere with the adhesion process regardless of whether a CB or the Er:YAG laser were used to prepare class V cavities when restored with the tested self-etching adhesive system.

PMID: 17618327 [PubMed - indexed for MEDLINE]

Tensile bond strength of glass fiber posts luted with different cements.

Braz Oral Res. 2007 Apr-Jun;21(2):159-64

Authors: Bonfante G, Kaizer OB, Pegoraro LF, do Valle AL

Proper selection of the luting agent is fundamental to avoid failure due to lack of retention in post-retained crowns. The objective of this study was to investigate the tensile bond strength and failure mode of glass fiber posts luted with different cements. Glass fiber posts were luted in 40 mandibular premolars, divided into 4 groups (n = 10): Group 1--resin-modified glass ionomer RelyX Luting; Group 2--resin-modified glass ionomer Fuji Plus; Group 3--resin cement RelyX ARC; Group 4--resin cement Enforce. Specimens were assessed by tensile strength testing and light microscopy analysis for observation of failure mode. The tensile bond strength values of each group were compared by ANOVA and Tukey test. The significance level was set at 5%. The failure modes were described as percentages. The following tensile strength values were obtained: Group 1--247.6 N; Group 2--256.7 N; Group 3--502.1 N; Group 4--477.3 N. There was no statistically significant difference between Groups 1 and 2 or between Groups 3 and 4, yet the resin cements presented significantly higher tensile bond strength values than those presented by the glass ionomer cements. Group 1 displayed 70% of cohesive failures, whereas Groups 2, 3 and 4 exhibited 70% to 80% of adhesive failures at the dentin-cement interface. We concluded that resin cements and glass ionomer cements are able to provide clinically sufficient retention of glass fiber posts, and that glass ionomer cements may be especially indicated when the application of adhesive techniques is difficult.

PMID: 17589652 [PubMed - in process]

Effect of centripetal and incremental methods in Class II composite resin restorations on gingival microleakage.

J Contemp Dent Pract. 2007;8(2):113-20

Authors: Ghavamnasiri M, Moosavi H, Tahvildarnejad N

AIM: The aim of this study was to evaluate the microleakage at gingival margins below the cementoenamel junction (CEJ) of Class II composite restorations using various placement techniques. METHODS AND MATERIALS: Sound human maxillary premolars were selected. Eighty slot-style cavities on the mesial or distal surfaces were prepared with the cervical margins located apical to the CEJ. The specimens were divided into two groups based on the restorative technique utilized (centripetal or incremental). Each group was then categorized into two subgroups according to the type of matrix used resulting in a total of four experimental groups as follows: IP=Incremental and Palodent matrix, IT = Incremental and Transparent matrix, CP= Centripetal and Palodent matrix, and CT = Centripetal and Transparent matrix. Following restoration with a total etch adhesive (Single Bond) and a resin composite (Z100), the teeth were thermocycled. Then specimens were immersed in 0.5% basic fuchsin dye for 24 hours at a temperature of 37 degrees C. Sectioned restorations were examined under a stereomicroscope (40X magnification), and the extent of the microleakage was scored and recorded. Data were analyzed using the Kruskal-Wallis non-parametric statistical test (P=0.05). RESULTS: In the four groups of the study no significant differences in the mean rank of microleakage were observed (p>0.05). CONCLUSION: When the gingival margin was located on cementum, the kind of matrix and filling technique did not reduce the microleakage.

PMID: 17277834 [PubMed - indexed for MEDLINE]

A comparison of two different methods and materials used to repair polycarbonate crowns.

J Contemp Dent Pract. 2007;8(2):105-12

Authors: Yilmaz A

AIM: The aim of this study was to evaluate the bond strength and crown-repair material interface of polycarbonate crown repaired using flowable resin composite and hybrid resin composite following two different surface preparations. METHODS AND MATERIALS: The facial surfaces of fifty-two polycarbonate crowns were flattened and roughened. Specimens were then divided into four test groups. A bonding agent alone (Groups 1 and 2) or a combination of methylmethacrylate (MMA) + bonding agent (Groups 3 and 4) was applied to the prepared surfaces. Then either a flowable (Groups 1 and 3) or a microfilled hybrid (Groups 2 and 4) resin composite was placed on the surfaces. Forty-eight of the original fifty-two specimens were used for shear bond strength testing. Failure types (adhesive, cohesive, and mixed) were evaluated. The remaining four specimens, one from each group, were used for crown-resin composite interface analysis using a scanning electron microscope (SEM). RESULTS: There were significant differences in both mean shear bond strength values and failure types (P<0.05). The SEM evaluation revealed a close interface relationship in Groups 3 and 4. CONCLUSION: MMA monomer application on a polycarbonate crown prior to application of an adhesive agent improved the shear bond strength of the repair material.

PMID: 17277833 [PubMed - indexed for MEDLINE]

Effect of two light-emitting diode (LED) and one halogen curing light on the microleakage of Class V flowable composite restorations.

J Contemp Dent Pract. 2007;8(2):80-8

Authors: Attar N, Korkmaz Y

AIM: The disadvantages of light cured composite resin materials with respect to microleakage are predominantly a result of polymerization shrinkage upon curing. It has been shown curing methods play a significant role in polymerization shrinkage of light-cured composite resins. The purpose of this study was to investigate the effect of light-emitting diode (LED) light curing units (LCUs) compared with a halogen LCU on microleakage of three different flowable composites using self-etch adhesives. METHODS AND MATERIALS: A total of 63 extracted human premolars were prepared with standardized Class V cavity preparations on the buccal and lingual surfaces of each tooth. The occlusal margin of the cavities was located on the enamel and the gingival margin was on dentin. Teeth were randomly assigned to three groups of 21 teeth each as follows: Group 1: Adper Prompt L-Pop + Filtek Flow (3M ESPE); Group 2: AdheSE + Tetric Flow (Ivoclar, Vivadent); and Group 3: Clearfil Protect Bond + Clearfil Protect Liner F (Kuraray Medical Inc.). All the groups were subdivided into three groups according to the curing lights used (n=7). Two LED LCUs, Elipar FreeLight and Elipar FreeLight 2 (3M ESPE), and one halogen-based LCU, Hilux Expert (Benlioglu ), were used. All teeth were then immersed in 0.5% basic fuchsin dye solution for 24 hours after thermocycling (500 cycles; between 5 degrees C to 55 degrees C). The teeth then were longitudinally sectioned and observed under a stereomicroscope (40X magnification) by two examiners. The degree of dye penetration was recorded separately for enamel and dentin. Data were analyzed with the Kruskal-Wallis and Mann-Whitney tests with the Bonferroni correction. RESULTS: No statistically significant differences in microleakage were observed between groups either on enamel or dentin (p>0.05). CONCLUSION: With the limitation of this in vitro study, the differences in microleakage between LCUs used were not statistically significantly different. Elipar Free Light 2 reduces curing time which can be considered as an advantage.

PMID: 17277830 [PubMed - indexed for MEDLINE]

Gap formation between different cavity walls and resin composite systems on primary and permanent teeth.

J Contemp Dent Pract. 2007;8(2):60-9

Authors: Tulunoglu O, Ulker AE

AIM: The aim of this study was to compare the effectiveness of five self-etching and etch-rinse dentin-bonding agents in achieving a gap-free adaptation between the restorative material and the dentin in primary and permanent teeth. METHODS AND MATERIALS: Gaps located at the restoration dentin interface were evaluated using scanning electron microscopy (SEM). RESULTS: There were more gaps on the corner of the cavities, but no significant difference was detected between different cavity walls (p>0,05). Statistical results of the SEM analysis revealed fewer gaps in the restorations made with self-etching dentin bonding agents than etch-rinse agents at the restoration-dentin interface in both primary and permanent teeth. CONCLUSION: Self-etching bonding systems were preferable in primary and permanent teeth according to the results of this study. However, further studies should be conducted to determine a favorable strategy to eliminate the gaps on the corners of cavities and maintain a gap-free adaptation between resin composite and tooth structure.

PMID: 17277828 [PubMed - indexed for MEDLINE]

The Knoop hardness of a composite resin polymerized with different curing lights and different modes.

J Contemp Dent Pract. 2007;8(2):52-9

Authors: Yazici AR, Kugel G, G&#xFC;l G

AIM: The purpose of this study was to compare the surface hardness of a hybrid composite resin polymerized with different curing lights. METHODS AND MATERIALS: Two 3.0 mm thick composite resin discs were polymerized in a prepared natural tooth mold using: (1) a conventional quartz-tungsten halogen light (QTH- Spectrum 800); (2) a high-intensity halogen light, Elipar Trilight (TL)-standard/exponential mode; (3) a high-intensity halogen light, Elipar Highlight (HL)-standard/soft-start mode; (4) a light-emitting diode, Elipar Freelight (LED); and (5) a plasma-arc curing light, Virtuoso (PAC). Exposure times were 40 seconds for the halogen and LED lights, and three and five seconds for the PAC light. Following polymerization, the Knoop hardness was measured at the bottom and the top surfaces of the discs. RESULTS: Significant differences were found between top and bottom Knoop Hardness number (KHN) values for all lights. The hardness of the top and bottom surfaces of both specimens cured by the PAC light was significantly lower than the other lights. No significant hardness differences were observed between the remaining curing units at the top of the 2.0 mm specimens. Significant differences were found between the LED and two modes of HL on the bottom surfaces. For the 3.0 mm thick samples, while significant differences were noted between LED and TL standard mode and between the two TL curing modes on the top, significant differences were only observed between QTH and the standard modes of TL and HL at the bottom.

PMID: 17277827 [PubMed - indexed for MEDLINE]

Effectiveness of second-generation light-emitting diode (LED) light curing units.

J Contemp Dent Pract. 2007;8(2):35-42

Authors: Campregher UB, Samuel SM, Fortes CB, Medina AD, Collares FM, Ogliari FA

AIM: The purpose of this study was to evaluate the effectiveness of three commercially available light emitting diode (LED) light curing units (LCU) (Elipar FreeLight--3M ESPE; UltraLume LED2--Ultradent; and Single V--BioArt) for polymerizing Z250-A3 composite (3M ESPE) using Knoop hardness, polymerization depth, and flexural strength properties. METHODS AND MATERIALS: The XL 2500 (3M ESPE) LCU, which is a conventional halogen unit, was used as a control. In all cases the curing time was 20 seconds. Hardness was determined 24 hours after composite cure for 10 samples of 8 mm diameter and 2 mm height for each LCU tested. Samples were stored dry in a light-proof container prior to testing. The depth of cure of the composite was measured immediately after composite polymerization for each LCU using three samples 4 mm in diameter and 6 mm in height. Flexural strength was determined for five samples 24 hours after immersion in distilled water at 37 degrees C. Each sample measured 25 mm in length, 2 mm in width, and 2 mm in height for each LCU tested. CONCLUSION: The results were treated statistically for comparison of the LCUs. In all cases the results obtained by LED LCUs were not different or were higher than a conventional halogen LCU. CLINICAL SIGNIFICANCE: Second generation LED LCUs were as effective as/or more effective than a halogen LCU for polymerization of the used composite. The present study shows second generation LEDs have the potential to replace halogen LCUs.

PMID: 17277825 [PubMed - indexed for MEDLINE]

The effect of thermocycling on the adhesion of self-etching adhesives on dental enamel and dentin.

J Contemp Dent Pract. 2007;8(2):17-24

Authors: El-Araby AM, Talic YF

AIM: The aim of the present study was to investigate the effectiveness of one total-etch self-priming adhesive and two one-step self-etching adhesive systems on the adhesion of a resin composite to both dentin and enamel. The effect of thermocycling on the adhesion was also investigated. The null hypothesis tested was thermocycling would not affect bond strengths to enamel and dentin treated with self-etching adhesives or a total-etch adhesive. METHODS AND MATERIALS: Two single-step self-etching adhesives [Xeno III (XE3) and Prompt L-Pop (PP)] and one two-step total-etch adhesive system (Prime & Bond NT) (P&B NT) were used in this study. Thirty caries-free unrestored human third molars were used to make specimens of enamel and dentin. Different adhesives were applied on enamel and dentin surfaces according to the manufacturer's instructions then hybrid composite restorative material was condensed on the surface using a mold. The bonded specimens were stored in distilled water at 37 masculineC for 24 hours before being tested. Half of the bonded specimens were tested for shear bond strength without thermocycling. The other half of the test specimens were thermocycled using a thermocycling apparatus in water baths held at 5 masculineC and 55 masculineC with a dwell time of one minute each for 10,000 cycles prior to shear testing. The mean shear bond strength before and after thermocycling was calculated, and the results were subjected to two-way analysis of variance (ANOVA) and repeated measure design to show the interaction between different materials and different times. RESULTS: The results showed shear bond strength on both enamel and dentin of the total-etch adhesive and the self-etching adhesives decreased after the specimens were subjected to thermocycling. CONCLUSIONS: The null hypothesis tested "thermocycling would not affect bond strengths treated with self-etching adhesives" was rejected. Furthermore, the study revealed the following: 1. The shear bond strength to both enamel and dentin of the total-etch adhesive and the self-etching adhesives decreased after the specimens were subjected to thermocycling. 2. XE3 achieved the highest bond strength to both enamel and dentin (26.994+/-1.17 and 25.22+/-1.26, respectively). 3. XE3 showed even better bonding after thermocycling to enamel and dentin than the total-etching system or PP. 4. Although PP bonded to enamel showed lower shear bond strength value than XE3, it has durable bond strength even after thermocycling.

PMID: 17277823 [PubMed - indexed for MEDLINE]

Effect of surface treatment on the shear bond strength of a resin-based cement to porcelain.

Braz Dent J. 2006;17(4):290-5

Authors: Nagayassu MP, Shintome LK, Uemura ES, Ara&#xFA;jo JE

The purpose of this in vitro study was to evaluate the effect of different surface treatments on the shear bond strength of a resin-based cement to porcelain. Sixty pairs of 50% aluminous porcelain discs were fabricated. In each pair, one disc measured 6 mm in diameter X 3 mm thickness (A) and the other measured 3 mm in diameter X 3mm thickness (B). The specimens were randomly assigned to 6 groups (n=10 pairs of discs), according to the surface treatment: etching with 10% hydrofluoric acid for 2 or 4 min (G1 and G2); 50-microm particle aluminum oxide sandblasting for 5 s (G3); sandblasting followed by etching for 2 or 4 min (G4 and G5) and control--no treatment (G6). A silane agent was applied to the treated surface of both discs of each pair. Bistite II DC dual-cure resin cement was applied and the B discs were bonded to their respective A discs. Specimens were stored in distilled water at 37 degrees C for 24 h and were tested in shear strength at a crosshead speed of 2 mm/min. Means in MPa were: G1: 14.21 +/- 4.68; G2: 8.92 +/- 3.02; G3: 10.04 +/- 2.37; G4: 12.74 +/- 5.15; G5: 10.99 +/- 3.35; G6: 6.09 +/- 1.84. Data were compared by one-way ANOVA and Tukey's test at 5% significance level. Bond strength recorded after 2-min acid etching was significantly higher than 4-min etching (p<0.05) and control (p<0.05), but did not differ significantly from sandblasting alone (p>0.05) or followed by etching for 2 or 4 min (p>0.05). Within the limitations of an in vitro study, it may be concluded that 2-min hydrofluoric acid etching produced a favorable micromechanical retention that enhanced resin cement bond strength to porcelain.

PMID: 17262141 [PubMed - indexed for MEDLINE]

Effect of refrigeration on bond strength of self-etching adhesive systems.

Braz Dent J. 2006;17(3):186-90

Authors: Borges GA, Spohr AM, de Oliveira WJ, Correr-Sobrinho L, Correr AB, Borges LH

The purpose of this study was to investigate the tensile bond strength to dentin of three self-etching adhesive systems at refrigerated and room temperatures. Seventy-eight bovine incisors were embedded in self-cured acrylic resin, abraded on a water-cooled lathe and polished with 400- and 600-grit sandpapers to obtain standard dentin surfaces. The specimens were randomly assigned to 6 groups (n=13). Clearfil SE Bond, AdheSE and One-Up Bond F adhesive systems at refrigerated (4 degrees C) and room temperatures (23 degrees C) were applied to dentin according to the manufacturers' instructions. A truncated composite resin (Herculite XRV) cone was bonded to dentin surface. The specimens were stored in distilled water at 37 degrees C for 24 h and submitted to tensile bond strength testing at a crosshead speed of 0.5 mm/min. Means in MPa were analyzed statistically by Student's t-test at 5% significance level. No statistically significant differences (p>0.05) were found between the adhesive systems applied at refrigerated and room temperatures. In conclusion, no adverse effects on tensile bond strength were observed when self-etching adhesive systems were used after being taken directly from the refrigerated storage.

PMID: 17262122 [PubMed - indexed for MEDLINE]

Morphological characterization of the tooth/adhesive interface.

Braz Dent J. 2006;17(3):179-85

Authors: Moura SK, Santos JF, Ballester RY

The purpose of this study was to assess the morphological characteristics of the tooth/adhesive interface using different adhesive systems in MOD restorations under scanning electron microscopy (SEM). The tested hypothesis was that the morphology of the bonding interface would vary in different areas of MOD restorations for the three adhesive systems. MOD cavities were prepared in 12 sound extracted human third molars and restored with Filtek Z250 composite resin and one of the following adhesive systems: Experimental ABF (n=4), Clearfil SE Bond (n=4) self-etching primers and Single Bond etch-and-rinse adhesive system (n=4). After 24-h storage in distilled water at 37 degrees C, teeth were sectioned and prepared for SEM. The interfacial morphology varied depending on the adhesive system and also on the evaluated area. The null hypothesis was accepted because the morphology of the tooth/adhesive interface reflected the characteristics of both the dental substrate and the adhesive systems.

PMID: 17262121 [PubMed - indexed for MEDLINE]

Porcelain laminate veneer restorations bonded with a three-liquid silane bonding agent and a dual-activated luting composite.

J Oral Sci. 2006 Dec;48(4):261-6

Authors: Matsumura H, Aida Y, Ishikawa Y, Tanoue N

This clinical report describes the fabrication and bonding of porcelain laminate veneer restorations in a patient with anterior open spaces. Laminate veneer restorations made of feldspathic porcelain were etched with 5% hydrofluoric acid, rinsed under tap water, ultrasonically cleaned with methanol, and primed with a chemically activated three-liquid silane bonding agent (Clearfil Porcelain Bond). The enamel surfaces were etched with 40% phosphoric acid, rinsed with water, and primed with a two-liquid bonding agent (Clearfil New Bond) that contained a hydrophobic phosphate (10-methacryloyloxydecyl dihydrogen phosphate; MDP). The restorations were bonded with a dual-activated luting composite (Clapearl DC). The veneers have been functioning satisfactorily for an observation period of one year. Combined use of the Clearfil bonding agents and Clapearl DC luting composite is an alternative to conventional materials for seating porcelain laminate veneer restorations, although the system is inapplicable to dentin bonding.

PMID: 17220627 [PubMed - indexed for MEDLINE]

Effect of metal priming agents on bonding characteristics of an acrylic resin joined to SUS XM27 steel.

J Oral Sci. 2006 Dec;48(4):215-8

Authors: Ishikawa Y, Kawamoto Y, Koizumi H, Furuchi M, Matsumura H, Tanoue N

The purpose of the current study was to evaluate the effect of functional monomers contained in the primers on adhesive bonding of a steel alloy. SUS XM27 steel was primed with one of the following materials; Alloy Primer, Estenia Opaque Primer, and V-Primer. The functional monomers in the primers were a phosphate (10-methacryloyloxydecyl dihydrogen phosphate; MDP) and a thione (6-(4-vinylbenzyl-n-propyl) amino-1,3,5-triazine-2,4-dithione, -dithiol tautomer; VTD) for Alloy Primer, MDP alone for Estenia, and VTD alone for V-Primer. The steel disks were bonded with an acrylic resin (Unifast Trad), and bond strength was determined. Of the three primers, both the Alloy Primer (33.3 MPa) and Estenia Opaque Primer (33.9 MPa) materials exhibited far better post-thermocycling bond strength than V-Primer (0 MPa). It can be concluded that the phosphate MDP is effective, whereas the thione VTD is ineffective for bonding SUS XM27 steel.

PMID: 17220619 [PubMed - indexed for MEDLINE]

Effect of different types of enamel conditioners on the bond strength of orthodontic brackets.

J Contemp Dent Pract. 2007 Jan 1;8(1):36-43

Authors: Davari AR, Yassaei S, Daneshkazemi AR, Yosefi MH

AIM: A unique characteristic of some new bonding systems in operative dentistry is they combine conditioning and priming agents into a single acidic primer solution for simultaneous use on both enamel and dentin. Combining conditioning and priming into a single treatment step results in improvement in both time and cost-effectiveness to the clinician and, indirectly, to the patient. The purpose of this study was to determine the effects of the use of a self-etching primer on the bond strength of orthodontic brackets and on the bracket/adhesive failure mode. METHODS AND MATERIALS: Thirty-six fresh bovine incisors were collected and stored in a solution of 0.1% (weight/volume) thymol. The criteria for tooth selection included intact buccal enamel, no cracks caused by the presence of the extraction forceps, and no defects. The teeth were cleansed and polished with pumice and rubber prophylactic cups for ten seconds. Brackets were bonded to the teeth according to one of three protocols following the manufacturers' instructions--Group 1: Conventional multistep bonding system (control group) (n=12); Group 2: Self-etching primer system (n=12); and Group 3: Acid+self-etching primer system (n=12). Specimens were loaded to failure in a Zwick test machine (Zwick GmbH & Co, Ulm, Germany). Shear bond strengths were measured at a crosshead speed of 5 mm/min. RESULTS: The mean shear bond strength in megapascals (Mpa) (standard deviation) were 11.7 (4.2), 10.5 (4.4), and 10.9 (4.8) for Groups 1, 2, and 3, respectively. The analysis of variance (ANOVA) was used to compare the three groups. The results indicated no significant difference in the bond strength between the three groups (P=0.800). The results of the Chi square test, evaluating the residual adhesives on the enamel surfaces, revealed no significant difference between the three groups (P=0.554). CONCLUSION: Results of the present in vitro study indicate the use of self-etching primers may be an alternative to conventional phosphoric acid pre-treatment in orthodontic bonding.

PMID: 17211503 [PubMed - indexed for MEDLINE]

The effect of finishing and polishing procedures on the surface roughness of composite resin materials.

J Contemp Dent Pract. 2007 Jan 1;8(1):27-35

Authors: Attar N

AIMS: The aims of this study were to evaluate the effect of various finishing and polishing procedures on the surface roughness of six different composite resin materials (Artemis Enamel, TPH Spectrum, Filtek A-110, Filtek Supreme Enamel, Solitaire 2, and Filtek P-60) as well as to evaluate the effectiveness of the surface sealant application (BisCover) on the surface roughness after finishing and polishing procedures of tested composites. METHODS AND MATERIALS: Specimens (n=168) measuring 5 mm in diameter x 2 mm in thickness were fabricated in a plexiglass well covered with a Mylar strip using six composite resins. A control group of seven specimens of each material received no polishing after being cured under the Mylar strip. Twenty-one specimens for each composite were randomly divided among three finishing and polishing groups (n=7). Each group was polished using a different system: Carbide bur/Sof-Lex disc, Carbide bur/Enhance disc with polishing paste, and Carbide bur/Edenta composite finishing kit. The average surface roughness (Ra, microm) of the control and treated specimens were measured with the Mitutoyo Surftest-402 Surface Roughness tester. After a surface sealant (BisCover) was applied to all treated specimens, according to manufacturer's instructions, the average roughness (Ra) was measured again. Results were statistically analyzed using analysis of variance (ANOVA) and the post-hoc Scheffe's test at a p<0.05 significance level. RESULTS: Significant differences were found for the surface roughness (p<0.05) with interaction among composite resins and the finishing systems used (p<0.05). Enhance/Biscover finishing and polishing procedure surface was not significantly different from the Mylar strip surface groups (p>0.05). The Mylar strip group was not significantly different from the Sof-Lex/BisCover and Edenta/BisCover groups. The ranking of mean Ra values by materials was as follows: Filtek Supreme Enamel < Filtek A110 < TPH Spectrum < Artemis <Filtek P-60 < Solitaire 2. The ranking of mean Ra values by polishing systems was as follows: Enhance/BisCover < Mylar Strip < Sof-Lex/BisCover < Edenta/BisCover < Sof-Lex < Enhance < Edenta. CONCLUSION: Smoother surfaces were recorded for the Enhance/BisCover and the Mylar strip-formed surface groups.The composite finishing kit Edenta significantly increased the Ra for all tested composites (p<0.05). But after finishing with Edenta, the use of a surface sealant (BisCover) significantly improved the surface smoothness of all tested composites (p<0.05). Use of BisCover surface sealant on anterior and posterior resin composite restorations after finishing and polishing procedures is recommended.

PMID: 17211502 [PubMed - indexed for MEDLINE]

A randomized clinical trial comparing 'one-step' and 'two-step' orthodontic bonding systems.

J Orthod. 2006 Dec;33(4):276-83; discussion 256-7

Authors: Manning N, Chadwick SM, Plunkett D, Macfarlane TV

OBJECTIVE: The primary objective of this prospective clinical trial was to assess the clinical bond failure rates of orthodontic brackets bonded using a self-etching primer (SEP), compared with brackets bonded using a conventional acid-etched technique with control adhesive (Transbond). A secondary aim was to investigate whether characteristics of the operator, patient or tooth bonded had any influence on bracket failure. DESIGN: Single-centre randomized controlled clinical trial. Thirty-four patients were bonded, each being randomly assigned to either the test or control adhesive. SETTING: NHS Hospital Orthodontic Department, Chester, UK. SUBJECTS: Orthodontic patients requiring fixed appliance treatment. MAIN OUTCOME MEASURES: Bond failure. MAIN OUTCOME RESULTS: Failure rates over the initial 6-month period were 2.0% (Transbond) and 1.7% (SEP) with no statistically significant difference between the two groups. Over the duration of the fixed appliance treatment, bond failure rates increased, but remained acceptable at 7.4 % (TB) and 7.0% (SEP), respectively. When operator, patient and tooth characteristics were analysed, only the bracket location was found to be significant. Maxillary brackets were more likely to fail than mandibular brackets (RR 0.47%; 95% CI 0.22, 1.03). The failure rate for brackets in our study was low when compared with previous studies. CONCLUSIONS: Both the acid-etched control and self-etching primer in combination with adhesive pre-coated brackets were successful for clinical bonding. Their combined failure rate was lower than that reported in similar trials.

PMID: 17142334 [PubMed - indexed for MEDLINE]

Antagonist enamel wears more than ceramic inlays.

J Dent Res. 2006 Dec;85(12):1097-100

Authors: Kr&#xE4;mer N, Kunzelmann KH, Taschner M, Mehl A, Garcia-Godoy F, Frankenberger R

Wear phenomena of ceramic inlays are not fully understood. The aim of the present study was to evaluate ceramic wear, antagonist enamel wear, and luting cement wear over 8 years. The two-fold null hypothesis was that there would be (1) no difference in wear behavior between ceramic and enamel, and (2) no influence of filler content of luting composites on composite wear. From 96 restorations, 36 Class II inlays from 16 participants were selected. For inlays with opposing enamel cusps (n=17), replicas of inlays and enamel were scanned with a 3-D laser scanner. Luting gaps of inlays (n=36) were analyzed with a profilometer, including 3-D data analysis. Ceramic and enamel wear increased between 4 and 8 years, with significantly higher values for enamel after 6 years (p<0.05). Luting gap wear increased continuously up to 8 years (p<0.05), with no influence of luting composites (p>0.05) and location of teeth (p>0.05).

PMID: 17122161 [PubMed - indexed for MEDLINE]

Electric-current-assisted application of self-etch adhesives to dentin.

J Dent Res. 2006 Dec;85(12):1092-6

Authors: Breschi L, Mazzoni A, Pashley DH, Pasquantonio G, Ruggeri A, Suppa P, Mazzotti G, Di Lenarda R, Tay FR

The use of electric current during the application of etch-and-rinse adhesive systems has been recently claimed to increase bonding of etch-and-rinse adhesives by enhancing substrate impregnation. The null hypothesis tested in this study was that electrically assisted application has no effect on bond strength of self-etching bonding systems. Three self-etch adhesives (Protect-Bond, Xeno III, and Prompt L-Pop) were applied with the aid of an electric signal-generating device (ElectroBond) and tested vs. controls prepared with the same disposable sponges but without electric current. Specimens bonded under the influence of electric current exhibited increased microtensile bond strength compared with the controls (p<0.05). High-resolution SEM analysis showed that bonding under the influence of electricity reduced interfacial nanoleakage. It is speculated that resin infiltration may be improved by the attraction of polar monomers by an electric current or by modification of the dentin surface charges, resulting in better water substitution or evaporation.

PMID: 17122160 [PubMed - indexed for MEDLINE]

Effect of the number of coats of simplified adhesive systems on microleakage of dentin-bordered composite restorations.

J Contemp Dent Pract. 2006 Nov 1;7(5):34-41

Authors: Harada TS, Pazinatto FB, Wang L, Atta MT

AIM: This study tested the null hypothesis that there is no difference on microleakage of dentin-bordered composite restorations using single or double coats of adhesive from one-bottle adhesive systems. METHODS AND MATERIALS: The enamel surface was removed from freshly extracted bovine teeth, and standardized Class V cavities (3 x 3 x 1.5 mm) were made at the cervical areas of buccal surfaces. Teeth were restored and grouped according to type of adhesive systems [Prime Bond 2.1 (PB2.1), Prime & Bond NT (PBNT), and Single Bond (SB)] and to the number of coats (one or two) to be used. The restorations were polished and immersed in a 0.5% aqueous solution of basic fuchsin for four hours. Teeth were then sectioned and the most infiltrated section of each tooth was selected under magnification, scanned, and quantitatively analyzed using a computer program. Data were analyzed using two-way analysis of variance (ANOVA) and Student-Newman-Keuls (a=0.05). RESULTS: Groups without filler content (PB2.1 and SB) showed no difference in microleakage using single or double coats. However, PBNT (with nanofiller) showed statistically less microleakage when only one coat was applied. The influence of the number of coats of the adhesive systems on dentin margin microleakage was material dependent. CONCLUSION: All adhesive systems demonstrated microleakage, however, it could be minimized using two coats of non-filled or one coat of a filled adhesive system.

PMID: 17091138 [PubMed - indexed for MEDLINE]

Microleakage of seven adhesive systems in enamel and dentin.

J Contemp Dent Pract. 2006 Nov 1;7(5):26-33

Authors: Silveira de Ara&#xFA;jo C, Incerti da Silva T, Ogliari FA, Meireles SS, Piva E, Demarco FF

AIM: The aim of this study was to evaluate the microleakage of seven adhesive systems on two substrates (enamel and dentin). METHODS AND MATERIALS: Class V cavities were performed in buccal and lingual surfaces of 56 bovine incisors. The cervical margin was located in dentin and the incisal margin in enamel. The specimens were randomly divided into seven groups (n=16), according to the adhesive system employed: Single Bond; Excite; One Step Plus; Gluma One Bond; Magic Bond; One Up Bond F; and One Coat Bond. The cavities were incrementally filled with a hybrid composite Filtek Z250 and polymerized with a XL 3000 light curing unit. After polishing, the specimens were submitted to thermal cycling followed by dye immersion. Leakage was evaluated under magnification (40X) based on a standard ranking. Data were subjected to statistical analysis (Kruskal-Wallis). RESULTS: Enamel margins exhibited lower leakage than dentin margins (p<0.01). The majority of the specimens were leakage-free and materials performed similarly. Conversely, in dentin most of the specimens exhibited the highest leakage degree and significant differences among materials (p<0.05) were found, with Excite exhibiting the lowest leakage degree. It was concluded enamel provided better sealing and the adhesive system was a significant factor only in dentin.

PMID: 17091137 [PubMed - indexed for MEDLINE]

The effect of two different polishing techniques on microleakage of new composites in Class V restorations.

J Contemp Dent Pract. 2006 Nov 1;7(5):18-25

Authors: Yalçin F, Korkmaz Y, Başeren M

AIM: The purpose of this study was to investigate the effect of polishing systems on the microleakage of a nanofill, a nanohybrid, and a microhybrid composite in Class V cavities. METHODS AND MATERIALS: Preparations were made at the cemento-enamel junction (CEJ) of 36 extracted human premolars. The teeth were randomly divided into three groups and restored with new resin composites according to the manufacturers' instructions as follows: Group 1, Filtek Supreme & Single Bond; Group 2, Grandio & Solobond; and Group 3, Artemis & Excite. The restorations were finished with diamond finishing burs. The restored/finished teeth were randomly divided into two groups and polished using the following systems: Super-Snap (Al2O2 coated, abrasive disc system, fine grit, and extra fine grit) and Astropol/Astrobrush (silicon-based abrasive polisher point and polisher brush). All specimens were thermocycled 1000 times with a 10 second dwell time. They were immersed in 0.5% aqueous basic fuchsin dye for 24 hours and then sectioned buccal-lingual-longitudinally through the center of both restorations of each tooth and evaluated under a stereomicroscope at 30X magnification. The degree of dye penetration was quantified. RESULT: No significant difference in leakage scores was observed in enamel margins (p=0.456, Kruskall Wallis test), but dentin margins were significantly affected by the different polishing systems (p=0.037, Kruskall Wallis test). The lower leakage scores were recorded for Astropol/Astrobrush polishing systems. The nanofill composite showed the least leakage among the test groups in this study. The most leakage was observed in nanohybrid composite resin (p<0.05, Mann Whitney U test). CONCLUSIONS: Under the conditions of this in vitro study: the microleakage resistance of composites at enamel margins is not significantly affected by the different polishing systems; the lowest leakage scores were recorded for Astropol/Astrobrush polishing techniques in different types of composites; and the ranking of the composite materials from most to least leakage at the dentin margins according to polishing techniques was Grandio >Artemis > Filtek Supreme.

PMID: 17091136 [PubMed - indexed for MEDLINE]

Apparent interfacial fracture toughness of resin/ceramic systems.

J Dent Res. 2006 Nov;85(11):1037-41

Authors: Della Bona A, Anusavice KJ, Mecholsky JJ

We suggest that the apparent interfacial fracture toughness (K(A)) may be estimated by fracture mechanics and fractography. This study tested the hypothesis that the K(A) of the adhesion zone of resin/ceramic systems is affected by the ceramic microstructure. Lithia disilicate-based (Empress2-E2) and leucite-based (Empress-E1) ceramics were surface-treated with hydrofluoric acid (HF) and/or silane (S), followed by an adhesive resin. Microtensile test specimens (n = 30; area of 1 +/- 0.01 mm(2)) were indented (9.8 N) at the interface and loaded to failure in tension. We used tensile strength (sigma) and the critical crack size (c) to calculate K(A) (K(A) = Ysigmac(1/2)) (Y = 1.65). ANOVA and Weibull analyses were used for statistical analyses. Mean K(A) (MPa.m(1/2)) values were: (E1HF) 0.26 +/- 0.06; (E1S) 0.23 +/- 0.06; (E1HFS) 0.30 +/- 0.06; (E2HF) 0.31 +/- 0.06; (E2S) 0.13 +/- 0.05; and (E2HFS) 0.41 +/- 0.07. All fractures originated from indentation sites. Estimation of interfacial toughness was feasible by fracture mechanics and fractography. The K(A) for the systems tested was affected by the ceramic microstructure and surface treatment.

PMID: 17062746 [PubMed - indexed for MEDLINE]

Effects of resin hydrophilicity on dentin bond strength.

J Dent Res. 2006 Nov;85(11):1016-21

Authors: Nishitani Y, Yoshiyama M, Donnelly AM, Agee KA, Sword J, Tay FR, Pashley DH

The purpose of this study was to determine if hydrophobic resins can be coaxed into dentin wet with ethanol instead of water. The test hypothesis was that dentin wet with ethanol would produce higher bond strengths for hydrophobic resins than would dentin wet with water. This study examined the microtensile bond strength of 5 experimental adhesives (50 wt% ethanol/50% comonomers) of various degrees of hydrophilicity to acid-etched dentin that was left moist with water, moist with ethanol, or air-dried. Following composite buildups, hourglass-shaped slabs were prepared from the bonded teeth for microtensile testing. For all 3 types of dentin surfaces, higher bond strengths were achieved with increased resin hydrophilicity. The lowest bond strengths were obtained on dried dentin, while the highest bond strengths were achieved when dentin was bonded moist with ethanol. Wet-bonding with ethanol achieved higher bond strengths with hydrophobic resins than were possible with water-saturated matrices.

PMID: 17062742 [PubMed - indexed for MEDLINE]

Influence of moisture conditions on dentin bond strength of single-step self-etch adhesive systems.

J Oral Sci. 2006 Sep;48(3):131-7

Authors: Chiba Y, Rikuta A, Yasuda G, Yamamoto A, Takamizawa T, Kurokawa H, Ando S, Miyazaki M

This study was conducted to clarify the influence of dentin surface moisture on bond strength of single-step self-etch adhesive systems. The adhesive systems used were Adper Prompt L-Pop (AP), Clearfil tri-S Bond (CT), Fluoro Bond Shake One (FB), G-Bond (GB), and One-Up Bond F Plus (OF). Bovine mandibular incisors were wet-ground with #600 SiC to expose the labial dentin. After rinsing with tap water, the dentin surface was dried with air for 10 sec (Dry condition) or blotted (Wet condition). Adhesives were applied according to each manufacturer's instructions, followed by resin composite polymerization. Ten samples per test group were stored in distilled water at 37 degrees C for 24 h, then shear tested at a crosshead speed of 1.0 mm/min. The data were analyzed by Student's t test and Tukey HSD test at a probability level of 0.05. The mean bond strengths for Dry condition ranged from 13.9 MPa to 18.2 MPa, and those for Wet condition ranged from 7.1 MPa to 18.4 MPa. Significantly lower bond strengths were obtained for the Wet condition for GB, FB, and OF. Failure after the test was commonly due to adhesive breakdown associated with partial cohesive failure in the dentin. These data suggest that air-drying of the dentin surface is appropriate for the adhesive systems tested.

PMID: 17023745 [PubMed - indexed for MEDLINE]

Influence of surface roughness on crack formation in a glass-ceramic bonded to a resin composite base.

J Oral Sci. 2006 Sep;48(3):125-30

Authors: Yamamoto T, Nishiura R, Momoi Y

The objective of the present study was to assess the influence of the roughness of a loaded surface on crack formation in a mica-based glass-ceramic bonded to a resin composite base. Five different surface roughnesses were created on glass-ceramic discs by serial wet-grinding with silicone carbide abrasives. The thicknesses of the ceramic discs were 1.50 +/- 0.01 mm. Resin composite discs were bonded to the ceramic surfaces opposite to the ground surfaces using an adhesive resin composite cement and a silane coupling agent. A compressive load was then applied at the center of the ground ceramic surface. The loads at initial radial and cone crack formations in the ceramic were measured macroscopically. In three of the five groups, the initial radial crack formations could not be observed due to the high roughness of these surfaces. Statistical analysis was performed using Student's t test for initial radial cracks and one-way ANOVA for the cone cracks. There were no significant differences between the two groups for the initial radial cracks or among the five groups for the cone cracks (P < 0.05). The roughness of the loaded surface had no influence on crack formation in the bonded mica-based glass-ceramic.

PMID: 17023744 [PubMed - indexed for MEDLINE]

In vitro microtensile bond strength of four adhesives tested at the gingival and pulpal walls of Class II restorations.

J Am Dent Assoc. 2006 Oct;137(10):1414-8

Authors: Purk JH, Healy M, Dusevich V, Glaros A, Eick JD

BACKGROUND: The authors compared the microtensile bond strength of teeth restored with four adhesives at the gingival and pulpal cavity walls of Class II resin-based composite restorations. METHODS: Five pairs of extracted third molars received two Class II preparations/restorations in each tooth. The authors randomly assigned each preparation to one of four adhesive groups: Adper Scotchbond Multipurpose Dental Adhesive (SBMP) (3M ESPE, St. Paul, Minn.), Clearfil SE Bond (CFSE) (Kuraray America, New York City), Prime & Bond NT (PBNT) (Dentsply Caulk, Milford, Del.) and PQ1 (Ultradent, South Jordan, Utah). They restored the teeth and obtained microtensile specimens from each cavity wall. Specimens were tested on a testing machine until they failed. RESULTS: The mean (+/- standard deviation) bond strengths (in megapascals) were as follows: SBMP (pulpal), 36.4 (17.2); SBMP (gingival), 29.7 (15.3); CFSE (pulpal), 50.8 (13.6); CFSE (gingival), 50.2 (14.0); PBNT (pulpal), 38.3 (19.2); PBNT (gingival), 38.9 (17.7); PQ1 (pulpal), 58.7 (8.7); and PQ1 (gingival), 54.5 (18.5). A two-way analysis of variance found an adhesive effect (P < .001) but no location effect (P >.05). CONCLUSIONS: PQ1 and CFSE performed the best. The results showed no significant difference in microtensile bond strength at the gingival wall versus the pulpal wall. CLINICAL IMPLICATIONS: Under in vitro conditions, a total-etch ethanol-based adhesive (PQ1) failed cohesively more often than did the other adhesives tested.

PMID: 17012721 [PubMed - indexed for MEDLINE]

Chemical interaction of phosphoric acid ester with hydroxyapatite.

J Dent Res. 2006 Oct;85(10):941-4

Authors: Fukegawa D, Hayakawa S, Yoshida Y, Suzuki K, Osaka A, Van Meerbeek B

Among functional monomers used in contemporary dental adhesives, 10-methacryloyloxydecyl dihydrogen phosphate (MDP) has been found to interact chemically with hydroxyapatite (HAp) most intensively and stably. This effect was thought to be the basis of the superior bonding effectiveness of MDP-based self-etch adhesives to enamel/dentin. To elucidate fully the chemical interaction and reactivity of MDP with HAp, we used (31)P CP-MAS NMR spectroscopy and powder x-ray diffraction. In an aqueous ethanol solution, Ca ions were leached from HAp to form, at short term, a MDP-calcium salt (CaMHP(2)) layered structure on the HAp surface. When MDP was allowed to interact for longer time (< 24 hrs), CaHPO(4).2H(2)O precipitated on top of this MDP-calcium salt layered structure. In conclusion, the intense chemical interaction of MDP with HAp must be ascribed to superficial dissolution of HAp induced by the MDP adsorption and subsequent deposition of MDP-calcium salt with a solubility lower than that of CaHPO(4).2H(2)O.

PMID: 16998137 [PubMed - indexed for MEDLINE]

Effect of different bonding conditions on the shear bond strength of two compomers to bovine dentin.

J Contemp Dent Pract. 2006 Sep 1;7(4):9-16

Authors: Al-Nahedh H, Ateyah NZ

AIM: Despite the improvements to compomer materials, the bond strength of these materials remains inferior to "composite/resin bonding" systems and limits their clinical use. The purpose of this study was to evaluate the effect of acidic conditioning with phosphoric acid and Prompt L-Pop (PLP) on the shear bond strength of two compomers Dyract AP (DAP) and Composan Glass (CG) to dentin. METHODS AND MATERIALS: Sixty extracted bovine teeth were used to test the shear bond strength of two compomers to flat dentin labial surfaces. The dentin specimens were randomly assigned to six groups of ten specimens each: Group 1: DAP and Prime & Bond NT (PBNT); Group 2: DAP/PBNT with a 15 second dentin etch prior to bonding; Group 3: DAP placed with PLP adhesive; Group 4: CG and Compobond NE (CBNE); Group 5: CG/CBNE with a 15 second dentin etch; and Group 6: CG placed with PLP adhesive. The specimens were stored at 37 masculineC with 100% humidity for 24 hours then mounted and sheared using an Instron Universal Testing Machine at a cross head speed of 0.5 mm/min. The results were recorded in Mega Pascals (MPa). The sheared specimens were examined under a light microscope, and the type of failure (adhesive, cohesive, or mixed) was recorded. RESULTS: The mean dentin shear bond strength value (MPa) for the groups was: Group 1 (11.6+/-3.9); Group 2 (13.2+/-3.3); Group 3 (12.4+/-2.0); Group 4 (13.0+/-4.3); Group 5 (19.3+/-3.7); and Group 6 (13.1+/-3.0). One way analysis of variance (ANOVA) and Tukey HSD post-hoc tests detected a significantly higher bond strength (P = 0.003) for group 5. For groups 1, 3, 4, and 6, the mode of failure was mostly adhesive. When acid etching of dentin was performed (groups 2 and 5), cohesive fracture within dentin was the predominant mode of failure. Acid etching and the use of PLP significantly reduced the number of adhesive fractures and reduced variability in the shear bond strength results. CONCLUSIONS: Acid etching significantly increased the shear bond strength of CG to dentin but did not affect DAP. The application of PLP resulted in a shear bond strength not statistically different from PBNT or CPNE. CG bond to dentin is improved with acid etching using phosphoric acid. However, PLP provided no significant improvement in the shear bond strength of DAP and CG.

PMID: 16957786 [PubMed - indexed for MEDLINE]

Effect of eugenol-based endodontic cement on the adhesion of intraradicular posts.

Braz Dent J. 2006;17(2):130-3

Authors: Alfredo E, de Souza ES, Marchesan MA, Paulino SM, Gariba-Silva R, Sousa-Neto MD

The present study evaluated, in vitro, the influence of an eugenol-based endodontic sealer (EndoFill) on the adhesion of intra-radicular posts cemented with a resin-based cement (Enforce) ou a zinc phosphate cement. Twenty-four single-rooted maxillary canines were divided into 2 groups (n=12) and obturated with either gutta-percha points plus EndoFill or gutta-percha points alone (no cement). In each group, half of intracanal posts (n=6) were cemented with Enforce resin-based cement and half with zinc phosphate cement. Specimens were submitted to pull-out test in an Instron machine and tensile force was applied at a crosshead speed of 0.5 mm/min until post dislodgement. The maximum forces required for post removal was recorded (N) and means were submitted to statistical analysis by Kruskal-Wallis test (p<0.01). Posts cemented with zinc phosphate cement were significantly more retentive (353.4 N) than those cemented with Enforce (134.9 N) (p<0.01). Regarding the influence of the eugenol-based cement (EndoFill) on post retention, there was statistically significant difference (p<0.01) only between the groups cemented with Enforce, i.e., in the canals filled with EndoFill + guta-percha there was lower bond strength than in the canals filled with gutta-percha points alone (101.5 and 168.2 N, respectively). In conclusion, the zinc-phosphate-based cement showed greater post retention than the resin-based cement. The findings of this study suggest that the eugenol-containing sealer interfered with the adhesive properties of the resin-based cement.

PMID: 16924340 [PubMed - indexed for MEDLINE]

Contraction stress in dentin adhesives bonded to dentin.

J Dent Res. 2006 Aug;85(8):728-32

Authors: Hashimoto M, de Gee AJ, Kaga M, Feilzer AJ

Adhesives cured under constrained conditions develop contraction stresses. We hypothesized that, with dentin as a bonding substrate, the stress would reach a maximum, followed by a continuous decline. Stress development was determined with a tensilometer for two total-etch systems and two systems with self-etching primers. The adhesives were placed in a thin layer between a glass plate and a flat dentin surface pretreated with phosphoric acid or self-etching primer. After an initial maximum shortly after light-curing, the stress decreased dramatically for the total-etch systems (70%) and, to a lesser extent, for the adhesives with self-etching primers (30%). The greater stress decrease for the total-etch systems was ascribed to water and/or solvents released into the adhesives from the fully opened dentinal tubules by the pulling/sucking action of the contraction stress. This happened less with the adhesives with self-etching primers, where the tubules remained mainly closed.

PMID: 16861290 [PubMed - indexed for MEDLINE]

Effect of thermal cycling on bond strengths of single-step self-etch adhesives to bovine dentin.

J Oral Sci. 2006 Jun;48(2):63-9

Authors: Asaka Y, Yamaguchi K, Inage H, Takamizawa T, Kurokawa H, Rikuta A, Kuroda T, Miyazaki M

The purpose of this study was to clarify the effect of thermal cycling on dentin bond strengths of single-step self-etch adhesives. Five commercially available single-step self-etch systems were used. The adhesives were applied to the dentin surfaces of bovine incisors, and then light-irradiated. Resin composites were condensed into a mold and light-irradiated. Bonded specimens were divided into two groups and stored in water at 37 degrees C for 24 h without thermal cycling, or in water at 37 degrees C for 24 h followed by 10,000 thermal cycles between 5 degrees C and 60 degrees C. Ten samples per group were tested for shear strength at a crosshead speed of 1.0 mm/min. The data were analyzed by Student's t test and Tukey HSD test at a probability level of 0.05. After 24 h of storage in water, the mean dentin bond strengths ranged from 9.3 MPa to 14.0 MPa. After 10,000 thermal cycles, the mean bond strengths remained unchanged. Failure after the test was commonly due to adhesive breakdown associated with partial cohesive failure of the resin. The present results suggest that the benefit of using single-step self-etch systems, in terms of simplifying the clinical procedure, might be acceptable even after thermal stresses.

PMID: 16858134 [PubMed - indexed for MEDLINE]

An in vitro assessment of prefabricated fiber post systems.

J Am Dent Assoc. 2006 Jul;137(7):1006-12

Authors: Teixeira EC, Teixeira FB, Piasick JR, Thompson JY

BACKGROUND: The authors conducted a study to characterize the in vitro retention, fracture and light transmission behavior of four different fiber-reinforced resin-based composite root canal posts. METHODS: The authors divided 44 teeth into four groups according to the type of post they would receive: parallel fiberglass posts, double-tapered fiber quartz posts, tapered fiberglass posts and two different types of parallel fiberglass posts. They prepared teeth and cemented posts with dual-cured resin cement. After the specimens aged, the authors conducted pull-out tests. For fracture testing, they loaded posts at 45 degrees in a universal testing machine. They determined load-to-fracture values and relative stiffness. They measured percentage of light transmission by means of a light microscope coupled with a spectrometer. RESULTS: Both tapered posts showed lower retention than did the parallel posts. Scanning electron microscropic analysis indicated that more cement adhered to the surfaces of the parallel fiberglass post than to those of the tapered fiberglass post. All posts demonstrated some plastic behavior, with the double-tapered fiber quartz post being stiffer than the others. CONCLUSION: Parallel fiber-reinforced composite posts showed better retention than did tapered posts when a dual-cured resin-based cement was used. Translucent prefabricated posts have limited light transmission. CLINICAL IMPLICATIONS: Parallel prefabricated fiber posts luted with dual-cured resin-based cement seem to be suitable for clinical application in endodontically treated teeth that require post-and-core restoration, showing good retention and acceptable fracture resistance.

PMID: 16803828 [PubMed - indexed for MEDLINE]

Has the 'total-etch' concept disappeared?

J Am Dent Assoc. 2006 Jun;137(6):817-20

Authors: Christensen GJ

PMID: 16803812 [PubMed - indexed for MEDLINE]

A retrospective clinical evaluation of two-unit cantilevered resin-bonded fixed partial dentures.

J Am Dent Assoc. 2006 Jun;137(6):783-8

Authors: Botelho MG, Leung KC, Ng H, Chan K

BACKGROUND: The authors conducted a study to examine the clinical performance of two-unit cantilevered resin-bonded fixed partial dentures (RBFPDs) that were inserted at The Prince Philip Dental Hospital, University of Hong Kong. METHODS: The authors recalled patients who had received two-unit cantilevered RBFPDs at least 24 months before the recall examination. The authors recorded the following data: patient's sex and age, operator's experience, prosthesis cementation date, endodontic treatment if performed, bone support, tooth mobility, the presence of shim-stock contacts on the abutment or pontic in intercuspal position, and the presence of aproximal axial contacts adjacent to the prosthesis. They also recorded the date of any debonding with subsequent treatment. They asked the patients qualitative questions about their prostheses. RESULTS: A total of 269 prostheses were placed in 214 patients and had a mean service life of 51.7 months +/- 19.5 months standard deviation, with a range of 13.2 to 141.6 months. Of 14 failed prostheses, 12 debonded, resulting in a success rate of 94.8 percent and clinical retention rate of 95.5 percent. No discernable rotation or drifting of the abutments was apparent in any of the prostheses. Overall patient satisfaction with RBFPDs was good, with an average assessment score of 8.5. CONCLUSIONS: The authors observed a 95.5 percent clinical retention rate of 269 two-unit RBFPDs, with no apparent drifting of the abutments. Longer-term follow-up studies are required. CLINICAL IMPLICATIONS: Two-unit RBFPDs are conservative and clinically retentive prostheses in the short to medium term.

PMID: 16803807 [PubMed - indexed for MEDLINE]

A randomised clinical trial to investigate bond failure rates using a self-etching primer.

Eur J Orthod. 2006 Oct;28(5):444-9

Authors: Murfitt PG, Quick AN, Swain MV, Herbison GP

This clinical trial evaluated, over a 12-month period, the performance of brackets bonded to teeth etched and primed with Transbond Plus Self-Etching Primer (SEP) when compared with a conventional separate two-step etch and primer system. Thirty-nine randomly selected patients requiring fixed appliance therapy were entered into the study. Random allocation of each etching system, along with a 'split-mouth cross-quadrant' design was used. A total of 661 brackets were placed by two operators. The failure and survival rates of the brackets were determined for age and gender of the patients, each etching system, operator, mode of failure, tooth position in the dental arch, and number of manipulations prior to curing the adhesive. Statistical analysis showed that SEP had a significantly higher bond failure rate (11.2 per cent) than the conventional etch and primer system (3.9 per cent) at the P = 0.001 level. Cox's proportional hazards regression showed the conventional etch and primer system to have a 60 per cent reduced chance of bracket failure over a 12-month observation period, while males had a 2.4 times increased risk compared with females. The predominant mode of failure was at the composite enamel interface for the SEP, while for the conventional etch and primer system, it was within the composite adhesive. No statistically significant differences were found for the failure rate with respect to the age of the patient, operator, tooth location, or the number of manipulations of the bracket. This in vivo study showed that brackets bonded using SEP had an increased clinical bond failure rate compared with the conventional, separate, etch and prime system.

PMID: 16763088 [PubMed - indexed for MEDLINE]

An in-vitro investigation into the use of a single component self-etching primer adhesive system for orthodontic bonding: a pilot study.

J Orthod. 2006 Jun;33(2):116-24

Authors: House K, Ireland AJ, Sherriff M

OBJECTIVE: This pilot study assessed force to debond (N); time, and site of bond failure of a single component self-etching primer (SEP) and adhesive system, Ideal 1 (GAC International Inc., USA) and compared it with the conventional acid etch and rinse regimen using 37% o-phosphoric acid solution and either Transbond XT (3M Unitek) or Ideal 1 adhesive. DESIGN: In vitro laboratory study. SETTING: Bristol Dental Hospital, UK. Sept 2003-Sept 2004. MATERIAL AND METHODS: Nine groups of 20 premolars were bonded using metal orthodontic brackets using three protocols: (1) 37% o-phosphoric acid etch and Transbond XT adhesive; (2) 37% o-phosphoric acid and Ideal 1 adhesive; (3) Ideal 1 SEP and Ideal 1 adhesive. Force to debond and locus of bond failure were determined at three time intervals. RESULTS: Enamel pre-treatment prior to bonding, namely SEP versus conventional etching had no significant effect on the median force to debond with the Ideal 1 adhesive. Similarly, when the enamel was conventionally etched, the adhesive type, namely Ideal 1 or Transbond XT, had no significant effect on the measured force to debond. However, there appeared to be differences in the locus of bond failure: failure predominated at the enamel/adhesive interface for the Transbond XT conventional etch group and at adhesive/bracket interface for the Ideal 1 SEP and adhesive group and the Ideal 1 adhesive conventional etch group. CONCLUSION: These results suggested that the complete Ideal 1 SEP and adhesive system might be successful in vivo leading therefore to a clinical trial. However, implications for clean up time are discussed and improvements to in vitro study designs are advised.

PMID: 16751433 [PubMed - indexed for MEDLINE]

Effect of dentinal surface preparation on bond strength of self-etching adhesive systems.

Braz Oral Res. 2006 Jan-Mar;20(1):52-8

Authors: Rocha PI, Borges AB, Rodrigues JR, Arrais CA, Giannini M

The aim of this study was to evaluate the effects of dentin surface treatments on the tensile bond strength (TBS) of the self-etching primer Clearfil SE Bond (CSE) and the one-step self-etching One-Up Bond F (OUB). The exposed flat dentin surfaces of twenty-four sound third molars were prepared with diamond bur at high-speed, carbide bur at low-speed or wet ground with #600 grit SiC paper. The adhesive systems were applied to the dentin surfaces and light-cured according to the manufacturers' instructions. A 6-mm high composite crown was incrementally built-up and each increment was light-cured for 40 seconds. After being stored in water (37 degrees C/24 h), the samples were serially sectioned parallel to the long axis, forming beams (n = 20) with a cross-sectional area of approximately 0.8 mm(2). The specimens were tested in a Universal Testing Machine at 0.5 mm/min. The cross-sectional area was measured and the results (MPa) were analyzed by two-way ANOVA and Tukey Test (p < 0.05). Overall, the groups treated with CSE exhibited the highest TBS for all surface treatments. Dentin surfaces prepared with carbide bur at low speed reduced TBS in the CSE group; however, OUB was not affected by surface treatments. The effect of surface abrasive methods on TBS was material-dependent.

PMID: 16729175 [PubMed - indexed for MEDLINE]

Bond strength of total-etch and self-etch dentin adhesive systems on peripheral and central dentinal tissue: a microtensile bond strength test.

J Contemp Dent Pract. 2006 May 1;7(2):26-36

Authors: Ye&#x15F;ilyurt C, Bulucu B

OBJECTIVE: The purpose of this study was to evaluate the microtensile bond strength (mu TBS) of four total-etch adhesives [Excite (EB), Prime&Bond NT (PBNT), Single Bond (SB), and One Coat Bond (OCB)] by comparing them to five self-etching adhesives (Clearfil SE Bond (CSEB), Xeno III (X III), Prompt L-Pop (PLP), AQ Bond (AQB), and Tyrian/One Step plus (TOSP)] at different dentinal areas. In addition the interface between the adhesive resins and dentin was examined using scanning electron microscopy (SEM). METHODS AND MATERIALS: Superficial occlusal dentin of extracted human molars was exposed and finished with wet 800-grit silicon carbide paper. A block of composite resin was then bonded to the molar samples with the above adhesives according to the manufacturers' instructions. After 24 hours in water at 37 degrees C, the specimens were sectioned into 1 mm thick slices and divided into two regional subgroups according to their relationship to pulp tissue using visual criteria: pulp center and pulp periphery. The slices were then trimmed for the microtensile bond test and subjected to a tensile force and crosshead speed of 1 mm/min. Two-way analysis of variance was performed for statistical analyses. In addition the bond strengths for nine adhesive systems for each dentinal area were compared using the Post-Hoc test. The resin-dentin interfaces for each adhesive system were observed under a SEM. RESULTS: Mean mu TBS ranged from (25.2 MPa) for TOSP to (48.9 MPa) for PBNT. The bond strengths of total-etch adhesive systems were not significantly different, and were higher than self-etch adhesive systems, except for CSEB (p<0.05). No significant regional difference was observed for all of the nine adhesive systems (p>0.05). SEM observation showed there is not a standard hybridization for adhesive systems. CONCLUSION: Different dentinal areas may not exhibit as great an influence on bond strengths using new adhesive systems.

PMID: 16685292 [PubMed - indexed for MEDLINE]

Evaluation of shear bond strength and SEM observation of all-in-one self-etching primer used for bonding of fissure sealants.

J Contemp Dent Pract. 2006 May 1;7(2):9-16

Authors: Al-Sarheed MA

OBJECTIVES: To evaluate and compare enamel shear bond strength of an all-in-one self-etching primer (Prompt L-Pop) to regular acid etch material when bonded to two-fissure sealant systems (Concise and Dyract Seal). METHOD AND MATERIALS: Forty newly extracted non-carious first permanent molars were embedded in a Teflon mold. The teeth were divided into four groups and each consisted of ten specimens. The bonding surfaces were treated with either Prompt L-Pop as recommended by the manufacturer or etched with phosphoric acid. After 24 hours of water storage, the specimens were evaluated for shear bond strength using an Instron testing machine. Scanning electron microscope (SEM) examinations were carried out to evaluate the failure sites of the sealants. RESULTS: The mean shear bond strengths using Prompt L-Pop were Concise: 23.46 MPa and Dyract Seal: 20.34 MPa. These values were higher than and statistically different from those of Dyract Seal (9.99 MPa) and Concise (8.85 MPa) when phosphoric acid was used. The failure was predominantly of the adhesive type. The SEM examination showed the failure of debonding was predominantly related to the type of etching systems used rather than the type of fissure sealants. CONCLUSION: The use of the all-in-one self-etching adhesive Prompt L-Pop improves the mean enamel shear bond strength of fissure sealants.

PMID: 16685290 [PubMed - indexed for MEDLINE]

Hydrolysis of functional monomers in a single-bottle self-etching primer--correlation of 13C NMR and TEM findings.

J Dent Res. 2006 May;85(5):422-6

Authors: Nishiyama N, Tay FR, Fujita K, Pashley DH, Ikemura K, Hiraishi N, King NM

Self-etching primers/adhesives that combine acidic methacrylate monomers with water in a single bottle are hydrolytically unstable and require refrigeration to extend their shelf-lives. This study tested the null hypothesis that one year of intermittent refrigeration of a 4-MET-containing simplified self-etching primer does not result in hydrolytic changes that are identifiable by transmission electron microscopy and (13)C NMR spectroscopy. Human dentin was bonded with UniFil Bond immediately after being unpacked, or after one year of intermittent refrigeration at 4 degrees C. Fresh and aged primers were analyzed by NMR for chemical changes. Ultrastructural observations indicated that there was an augmentation in etching capacity of the aged adhesive that was not accompanied by resin infiltration or effective polymerization. New NMR peaks detected from the aged ethanol-based primer confirmed that degradation occurred initially via esterification with ethanol, followed by hydrolysis of both ester groups in the 4-MET. Hydrolysis of functional methacrylate monomers occurs despite intermittent refrigeration.

PMID: 16632754 [PubMed - indexed for MEDLINE]

Neurobehavioral effects of dental amalgam in children: a randomized clinical trial.

JAMA. 2006 Apr 19;295(15):1784-92

Authors: DeRouen TA, Martin MD, Leroux BG, Townes BD, Woods JS, Leit&#xE3;o J, Castro-Caldas A, Luis H, Bernardo M, Rosenbaum G, Martins IP

CONTEXT: Dental (silver) amalgam is a widely used restorative material containing 50% elemental mercury that emits small amounts of mercury vapor. No randomized clinical trials have determined whether there are significant health risks associated with this low-level mercury exposure. OBJECTIVE: To assess the safety of dental amalgam restorations in children. DESIGN: A randomized clinical trial in which children requiring dental restorative treatment were randomized to either amalgam for posterior restorations or resin composite instead of amalgam. Enrollment commenced February 1997, with annual follow-up for 7 years concluding in July 2005. SETTING AND PARTICIPANTS: A total of 507 children in Lisbon, Portugal, aged 8 to 10 years with at least 1 carious lesion on a permanent tooth, no previous exposure to amalgam, urinary mercury level <10 microg/L, blood lead level <15 microg/dL, Comprehensive Test of Nonverbal Intelligence IQ > or =67, and with no interfering health conditions. INTERVENTION: Routine, standard-of-care dental treatment, with one group receiving amalgam restorations for posterior lesions (n = 253) and the other group receiving resin composite restorations instead of amalgam (n = 254). MAIN OUTCOME MEASURES: Neurobehavioral assessments of memory, attention/concentration, and motor/visuomotor domains, as well as nerve conduction velocities. RESULTS: During the 7-year trial period, children had a mean of 18.7 tooth surfaces (median, 16) restored in the amalgam group and 21.3 (median, 18) restored in the composite group. Baseline mean creatinine-adjusted urinary mercury levels were 1.8 microg/g in the amalgam group and 1.9 microg/g in the composite group, but during follow-up were 1.0 to 1.5 microg/g higher in the amalgam group than in the composite group (P<.001). There were no statistically significant differences in measures of memory, attention, visuomotor function, or nerve conduction velocities (average z scores were very similar, near zero) for the amalgam and composite groups over all 7 years of follow-up, with no statistically significant differences observed at any time point (P values from .29 to .91). Starting at 5 years after initial treatment, the need for additional restorative treatment was approximately 50% higher in the composite group. CONCLUSIONS: In this study, children who received dental restorative treatment with amalgam did not, on average, have statistically significant differences in neurobehavioral assessments or in nerve conduction velocity when compared with children who received resin composite materials without amalgam. These findings, combined with the trend of higher treatment need later among those receiving composite, suggest that amalgam should remain a viable dental restorative option for children. TRIAL REGISTRATION: clinicaltrials.gov Identifier: NCT00066118.

PMID: 16622140 [PubMed - indexed for MEDLINE]

Neuropsychological and renal effects of dental amalgam in children: a randomized clinical trial.

JAMA. 2006 Apr 19;295(15):1775-83

Authors: Bellinger DC, Trachtenberg F, Barregard L, Tavares M, Cernichiari E, Daniel D, McKinlay S

CONTEXT: No randomized trials have been published that address the concern that inhalation of mercury vapor released by amalgam dental restorations causes adverse health effects. OBJECTIVE: To compare the neuropsychological and renal function of children whose dental caries were restored using amalgam or mercury-free materials. DESIGN AND SETTING: The New England Children's Amalgam Trial was a 2-group randomized safety trial involving 5 community health dental clinics in Boston, Mass, and 1 in Farmington, Me, between September 1997 and March 2005. PARTICIPANTS AND INTERVENTION: A total of 534 children aged 6 to 10 years at baseline with no prior amalgam restorations and 2 or more posterior teeth with caries were randomly assigned to receive dental restoration of baseline and incident caries during a 5-year follow-up period using either amalgam (n=267) or resin composite (n =267) materials. MAIN OUTCOME MEASURES: The primary neuropsychological outcome was 5-year change in full-scale IQ scores. Secondary outcomes included tests of memory and visuomotor ability. Renal glomerular function was measured by creatinine-adjusted albumin in urine. RESULTS: Children had a mean of 15 tooth surfaces (median, 14) restored during the 5-year period (range, 0-55). Assignment to the amalgam group was associated with a significantly higher mean urinary mercury level (0.9 vs 0.6 microg/g of creatinine at year 5, P<.001). After adjusting for randomization stratum and other covariates, no statistically significant differences were found between children in the amalgam and composite groups in 5-year change in full-scale IQ score (3.1 vs 2.1, P = .21). The difference in treatment group change scores was 1.0 (95% confidence interval, -0.6 to 2.5) full-scale IQ score point. No statistically significant differences were found for 4-year change in the general memory index (8.1 vs 7.2, P = .34), 4-year change in visuomotor composite (3.8 vs 3.7, P = .93), or year 5 urinary albumin (median, 7.5 vs 7.4 mg/g of creatinine, P = .61). CONCLUSIONS: In this study, there were no statistically significant differences in adverse neuropsychological or renal effects observed over the 5-year period in children whose caries were restored using dental amalgam or composite materials. Although it is possible that very small IQ effects cannot be ruled out, these findings suggest that the health effects of amalgam restorations in children need not be the basis of treatment decisions when choosing restorative dental materials. TRIAL REGISTRATION: clinicaltrials.gov Identifier: NCT00065988.

PMID: 16622139 [PubMed - indexed for MEDLINE]

Influence of light intensity on dentin bond strength of self-etch systems.

J Oral Sci. 2006 Mar;48(1):21-6

Authors: Yamamoto A, Tsubota K, Takamizawa T, Kurokawa H, Rikuta A, Ando S, Takigawa T, Kuroda T, Miyazaki M

The purpose of this study was to investigate the influence of light intensity on dentin bond strengths of four self-etch adhesive systems. The light intensities used to polymerize specimens were controlled at levels of 150, 300, 600, and 900 mW/cm2. The two-step self-etch adhesive systems Imperva Fluoro Bond and Mac Bond II, and the one-step self-etch systems Fluoro Bond Shake-One and One-Up Bond F Plus were used with their corresponding light-cured resins. Labial surfaces of lower bovine incisors were ground with #600 grit SiC paper to expose the dentin. The dentin surfaces were treated according to each manufacturer's instructions and bonded with resin composites. A shear bond strength test was performed and the data were analyzed by one-way ANOVA followed by Newman-Keuls multiple comparison at a level of 0.05. Statistical analysis of the data indicated that light intensity affected the dentin bond strengths of the adhesive systems tested. Significantly lower bond strengths were obtained by exposure to 150 mW/cm2, and there were no differences between the bond strengths obtained at 600 and 900 mW/cm2 for all the adhesive systems used. Further research will be required to clarify the irradiance-dependent properties of light-cured resin adhesive systems.

PMID: 16617197 [PubMed - indexed for MEDLINE]

Removal resistance of glass-fiber and metallic cast posts with different lengths.

J Oral Sci. 2006 Mar;48(1):15-20

Authors: Braga NM, Paulino SM, Alfredo E, Sousa-Neto MD, Vansan LP

This study evaluated the strength required to remove glass-fiber and metallic cast posts with different lengths. Sixty endodontically treated canines were included and their roots were embedded in acrylic resin after discarding the crowns. Samples were randomly assigned to 3 groups according to the post length (n = 20): I- 6 mm, II - 8 mm and III- 10 mm. Each group was divided into 2 subgroups based on the post material (n = 10): A- glass fiber or B- metallic cast. Post-space was prepared with Fibrekor Post Kit attached to a parallelometer. In subgroup A, prefabricated glass fiber posts from Fibrekor Post Kit were utilized. In metallic post group (subgroup B), an impression of post space was obtained, followed by casting. All posts were luted with Panavia F cement. A universal testing machine determined the force required to dislodge each post. ANOVA analysis indicated significant differences (P < 0.01) among post length. Tukey test showed that posts with 10 mm-length showed higher resistance on removal than posts with 6 mm-length. Posts with 8 mm-length did not exhibit difference when compared to 6 and 10 mm posts. No significant differences (P > 0.05) were observed between the tested post materials. It was concluded that the type of post did not influence the removal resistance and that posts with 10 mm-length required greater force to be dislodged.

PMID: 16617196 [PubMed - indexed for MEDLINE]

Resin tag length of one-step and self-etching adhesives bonded to unground enamel.

Bull Tokyo Dent Coll. 2005 Aug;46(3):43-9

Authors: Sundfeld RH, de Oliveira CH, da Silva AM, Briso AL, Sundfeld ML

Length of resin tags yielded by utilization of an one-step conventional adhesive system and self-etching adhesive system on unground enamel was observed. In study Groups I and III, the enamel surface was etched for 60 seconds with 35% phosphoric acid gel and adhesive systems PQ1 (Ultradent Products, Inc) and Adper Prompt L Pop (3M/ESPE) were applied. Adper Prompt L Pop (3M/ESPE) was also applied in Group II in accordance with the manufacturer's recommendations. After application of these adhesive systems to dental enamel, specimens were prepared for light microscopy analysis to ascertain degree of penetration (x400). The results were submitted to an analysis of variance at the 5% level; whenever there was significance, the Tukey test was applied at the 5% level. It was found that acid etching prior to application of conventional and self-etching adhesive materials provided higher penetration of the adhesive into the unground enamel surface compared to that achieved solely by application of self-etching adhesive.

PMID: 16598180 [PubMed - indexed for MEDLINE]

Evaluation of a self-limiting concept in dentinal caries removal.

J Dent Res. 2006 Mar;85(3):282-6

Authors: Silva NR, Carvalho RM, Pegoraro LF, Tay FR, Thompson VP

The mechanical removal of dentinal caries traditionally involves the use of tactile sensation and/or caries-indicating dyes. This study tested the hypothesis that self-limiting polymer burs are as effective as conventional carbide burs in creating substrates for dentin bonding. Carious dentin from extracted human molars was removed with carbide or polymer burs, with dental explorer hardness as the end-point for caries removal. Dentin substrates were bonded with etch-and-rinse or self-etch adhesives and prepared for microtensile bond testing and transmission electron microscopy. For each bur type, there was no difference in bond strength between adhesives. However, the polymer bur surface exhibited significantly lower bond strengths than the carbide bur, and both were lower than flat, non-carious dentin controls. TEM revealed areas of incompletely removed, denatured caries-infected dentin in the polymer bur specimens. These first-generation polymer burs might best be utilized for deep caries removal where pulpal exposure is a concern.

PMID: 16498079 [PubMed - indexed for MEDLINE]