Compressive strength of glass ionomer cements using different specimen dimensions.

Braz Oral Res. 2007 Jul-Sep;21(3):204-8

Authors: Mallmann A, Ataíde JC, Amoedo R, Rocha PV, Jacques LB

The purpose of this study was to evaluate the compressive strength of two glass ionomer cements, a conventional one (Vitro Fil - DFL) and a resin-modified material (Vitro Fil LC - DFL), using two test specimen dimensions: One with 6 mm in height and 4 mm in diameter and the other with 12 mm in height and 6 mm in diameter, according to the ISO 7489:1986 specification and the ANSI/ADA Specification No. 66 for Dental Glass Ionomer Cement, respectively. Ten specimens were fabricated with each material and for each size, in a total of 40 specimens. They were stored in distilled water for 24 hours and then subjected to a compressive strength test in a universal testing machine (EMIC), at a crosshead speed of 0.5 mm/min. The data were statistically analyzed using the Kruskal-Wallis test (5%). Mean compressive strength values (MPa) were: 54.00 +/- 6.6 and 105.10 +/- 17.3 for the 12 mm x 6 mm sample using Vitro Fil and Vitro Fil LC, respectively, and 46.00 +/- 3.8 and 91.10 +/- 8.2 for the 6 mm x 4 mm sample using Vitro Fil and Vitro Fil LC, respectively. The resin-modified glass ionomer cement obtained the best results, irrespective of specimen dimensions. For both glass ionomer materials, the 12 mm x 6 mm matrix led to higher compressive strength results than the 6 mm x 4 mm matrix. A higher variability in results was observed when the glass ionomer cements were used in the larger matrices.

PMID: 17710284 [PubMed - in process]

Tensile bond strength of glass fiber posts luted with different cements.

Braz Oral Res. 2007 Apr-Jun;21(2):159-64

Authors: Bonfante G, Kaizer OB, Pegoraro LF, do Valle AL

Proper selection of the luting agent is fundamental to avoid failure due to lack of retention in post-retained crowns. The objective of this study was to investigate the tensile bond strength and failure mode of glass fiber posts luted with different cements. Glass fiber posts were luted in 40 mandibular premolars, divided into 4 groups (n = 10): Group 1--resin-modified glass ionomer RelyX Luting; Group 2--resin-modified glass ionomer Fuji Plus; Group 3--resin cement RelyX ARC; Group 4--resin cement Enforce. Specimens were assessed by tensile strength testing and light microscopy analysis for observation of failure mode. The tensile bond strength values of each group were compared by ANOVA and Tukey test. The significance level was set at 5%. The failure modes were described as percentages. The following tensile strength values were obtained: Group 1--247.6 N; Group 2--256.7 N; Group 3--502.1 N; Group 4--477.3 N. There was no statistically significant difference between Groups 1 and 2 or between Groups 3 and 4, yet the resin cements presented significantly higher tensile bond strength values than those presented by the glass ionomer cements. Group 1 displayed 70% of cohesive failures, whereas Groups 2, 3 and 4 exhibited 70% to 80% of adhesive failures at the dentin-cement interface. We concluded that resin cements and glass ionomer cements are able to provide clinically sufficient retention of glass fiber posts, and that glass ionomer cements may be especially indicated when the application of adhesive techniques is difficult.

PMID: 17589652 [PubMed - in process]

Comparative evaluation of the marginal sealing ability of Fuji VII and Concise as pit and fissure sealants.

J Contemp Dent Pract. 2007;8(4):10-8

Authors: Ganesh M, Shobha T

AIM: The anatomical pits and fissures of the teeth have long been recognized as susceptible areas for the initiation of dental caries. The extreme vulnerability to decay of these pits and fissures on the occlusal surfaces has prompted dental scientists to seek methods of caries prevention. Motivated by the role of pit and fissure sealants in caries prevention, the aim of this study was to compare the efficacy of Fuji VII glass ionomer sealant and Concise resin-based sealant. METHODS AND MATERIALS: An in vitro study was undertaken using forty premolars extracted for orthodontic reasons. The teeth were divided into two groups and sealants were applied. One was an experimental group using Fuji VII as a pit and fissure sealant and the other a control group using Concise. The teeth were kept in gentian violet dye for 24 hours, the sectioned samples were observed for the extent of dye penetration, and scores were based on established scoring criteria. RESULTS: The comparison of the performance of the two groups showed a statistically significant difference. CONCLUSION: The Concise resin-based sealant performed better in terms of sealing ability than did the Fuji VII glass ionomer sealant.

PMID: 17486182 [PubMed - indexed for MEDLINE]

Shear bond strength of resin modified glass ionomer cement bonded to different tooth-colored restorative materials.

J Contemp Dent Pract. 2007;8(2):25-34

Authors: Taher NM, Ateyah NZ

AIM: The aim of this study was to determine in vitro the shear bond strength (MPa) and the type of bond failure when resin-modified glass ionomer cement (RMGIC) was bonded with different tooth-colored restorative materials. METHODS AND MATERIALS: The RMGIC tested was Fuji II LC (FL) and the tooth-colored restorative materials used were composite resin Point-4 (P4), Compomer Dyract AP (DY), and Ormocere Admira (AD). A total number of 60 FL specimens were prepared using Teflon molds. The specimens were divided into six equal groups. Each group of ten specimens was bonded to a tested tooth-colored restorative material as follows: Group I--etched FL bonded to P4; Group II--non-etched FL bonded to P4; Group III--etched FL bonded to DY; Group IV--non-etched FL bonded to DY; Group V--etched FL bonded to AD; and Group VI--non-etched FL bonded to AD. The specimens were stored in distilled water at 37 degrees C for 24 hours. The shear bond strength was measured in a universal testing machine, and the fractured surfaces were examined under a stereomicroscope. RESULTS: The results of the shear bond strength indicated the lowest mean value (14.46 MPa) was in Group III, and this was significantly different from the values of other groups (p<0.05). However, Groups V and VI recorded the highest mean values (24.5 MPa and 28.39 MPa) which were significantly different (p<0.05) when compared to other groups. Groups I, II, and IV showed no significant difference with mean values of 20.06, 19.99, and 20.1 MPa which were significantly different from other groups (p<0.05). CONCLUSION: AD showed the highest shear bond strength to RMGIC. All groups demonstrated a cohesive failure in FL except for Group IV where a cohesive failure in DY was recorded. AD showed good shear bond strength when laminated with FL.

PMID: 17277824 [PubMed - indexed for MEDLINE]

Water sorption of resin-modified glass-ionomer cements photoactivated with LED.

Braz Oral Res. 2006 Oct-Dec;20(4):342-6

Authors: Cefaly DF, Wang L, de Mello LL, dos Santos JL, dos Santos JR, Lauris JR

The Light Emitting Diodes (LED) technology has been used to photoactivate composite resins and there is a great number of published studies in this area. However, there are no studies regarding resin-modified glass-ionomer cements (RMGIC), which also need photoactivation. Therefore, the aim of this study was to evaluate water sorption of two RMGIC photoactivated with LED and to compare this property to that obtained with a halogen light curing unit. A resin composite was used as control. Five specimens of 15.0 mm in diameter x 1.0 mm in height were prepared for each combination of material (Fuji II LC Improved, Vitremer, and Filtek Z250) and curing unit (Radii and Optilight Plus) and transferred to desiccators until a constant mass was obtained. Then the specimens were immersed into deionized water for 7 days, weighed and reconditioned to a constant mass in desiccators. Water sorption was calculated based on weight and volume of specimens. The data were analyzed by two-way ANOVA and Tukey test (p < 0.05). Specimens photocured with LED presented significantly more water sorption than those photocured with halogen light. The RMGIC absorbed statistically significant more water than the resin composite. The type of light curing unit affected water sorption characteristics of the RMGIC.

PMID: 17242796 [PubMed - indexed for MEDLINE]

In vitro Characteristics of a Glass Ionomer Cement.

Skull Base Surg. 1998;8(4):175-80

Authors: Driscoll CL, Green JD, Beatty CW, McCaffrey TV, Marrs CD

Glass ionomer cements were first described by Wilson and Kent and have been used in dentistry since 1969. It has been recommended for bridging ossicular chain defects, fixation of ossicular chain prosthesis, anchoring of cochlear implants, mastoid obliteration, and repair of tegmen and posterior canal wall defects. The biocompatability and stability of this material over time is vital to its usefulness in neurotologic surgery. The purpose of this study was to assess the stability of a glass ionomer cement in the presence of bacteria and in different pH environments. We demonstrated that bacteria readily adhere to the surface and their presence is associated with accelerated loss of matrix. We found the cement to be susceptible to low pH and to release a visible cloud of debris upon contact with fluid. Calcium concentration in the solution was elevated at all pH levels. Although we are able to demonstrate these findings in vitro the clinical relevance is unclear. There have been several cases of aseptic meningitis possibly due to intracranial release of components of the cement. Until further studies are done use of the cement in contact with cerebral spinal fluid should be avoided. This cement, or a similar material, would be useful in neurotologic surgery but prior to widespread use further testing should be done to assess safety.

PMID: 17171062 [PubMed - in process]

Effects of repeated fluoride varnish application on different restorative surfaces.

J Contemp Dent Pract. 2006 Nov 1;7(5):54-61

Authors: Salama FS, Schulte KM, Iseman MF, Reinhardt JW

AIM: The aim of this study was to assess the effect of repeated (twice) applications of two fluoride varnishes (Duraflor and CavityShield) on the surface micromorphology of a high-viscosity glass ionomer (Fuji IX GP), a compomer (F2000), and a flowable composite (Filtek Flow) using a profilometer and scanning electron microscope (SEM). METHODS AND MATERIALS: Fifteen specimens were prepared from each material, surface roughness (Ra) was measured with a profilometer, and an impression was made for epoxy replicas. The fluoride varnishes were applied to the experimental specimens of each material at repeated intervals of 48 hours. For all specimens, Ra was measured and SEM replicas were examined. RESULTS: The final Ra of glass ionomer was 3.49 +/- 0.59 (mean +/- SD) for CavityShield, 4.69 +/- 1.33 for Duraflor, and 2.96 +/- 1.53 for the controls. The final Ra of flowable composite was 0.53 +/- 0.20 for CavityShield, 2.61 +/- 3.08 for Duraflor, and 0.15 +/- 0.09 for controls. For glass ionomer and flowable composite, Duraflor was associated with a significantly higher roughness at the final measurement compared to controls (P < 0.05). SEM micrographs showed differing surface topographies which in many specimens confirmed Ra analysis. CONCLUSION: Fuji IX GP and Filtek Flow showed significantly higher roughness after two applications of Duraflor compared to controls.

PMID: 17091140 [PubMed - indexed for MEDLINE]

One-year clinical evaluation of two resin composites, two polymerization methods, and a resin-modified glass ionomer in non-carious cervical lesions.

J Contemp Dent Pract. 2006 Nov 1;7(5):42-53

Authors: Koubi S, Raskin A, Bukiet F, Pignoly C, Toca E, Tassery H

AIM: The aim of this study was to examine clinically relevant data on four restorative procedures for non-carious cervical lesions using United States Public Health Service (USPHS)-compatible clinical and photographic criteria and to compare different methods of analyzing clinical data. METHODS AND MATERIALS: Fourteen patients with at least one or two pairs of non-carious lesions under occlusion and a mean age of 50 were enrolled in this study. A total of 56 restorations (14 with each material) were placed by three experienced, calibrated dental practitioners. Two other experienced and calibrated practitioners, under single-blind conditions, followed up on all restorations for a period of one year. Three materials were randomly placed: a micro-hybrid composite with two polymerization methods (G1 and G2), a flowable micro-hydrid composite (G3), and a resin-modified glass ionomer (G4). Statistical analysis was performed using the Kruskall-Wallis test (p<0.05) and a Mann-Whitney U modified test with a corrected significance level. RESULTS: At the one year evaluation time, there were no restorations with secondary caries and the retention rates in G1 (IntenS with a hard polymerization), G2 (IntenS with a soft polymerization), G3 (Filtek flow), and G4 (Fuji II LC) were 85.7% (two losses), 92.8% (one loss), 100%, and 100%, respectively. The total visual comparison of the results at baseline (15 days later) showed significant differences only with the clinical acceptance criterion: G1 was different from G2, with a soft polymerization device (p<0.05). In terms of surface quality at one year, G1, G2, and G3 exhibited a statistically significant difference from G4, p<0.05. The digital analysis at baseline showed significant differences only with the clinical acceptance criterion: G1=G2 was different from G3=G4, p<0.05. At one year, only the microporosity criterion showed any statistical differences: G1=G2=G3 was different from G4, p<0.05. CONCLUSIONS: The resin-modified glass ionomer was easier to use and had a high retention rate, but it failed in terms of surface quality (visual mode) and porosity (digital mode) criteria compared to the others groups. Overall results showed no difference between groups G1 (hard-polymerized) and G2 (soft-polymerized), and only G1 was affected by the marginal edge (p<0.03) and integrity criteria (p<0.02) at one year.

PMID: 17091139 [PubMed - indexed for MEDLINE]

A clinical evaluation of resin-based composite and glass ionomer cement restorations placed in primary teeth using the ART approach: results at 24 months.

J Am Dent Assoc. 2006 Nov;137(11):1529-36

Authors: Ersin NK, Candan U, Aykut A, On&#xE7;ağ O, Eronat C, Kose T

BACKGROUND: The authors evaluated the 24-month performance of a packable resin-based composite/dentin bonding system and a high-viscosity glass ionomer cement (GIC) in restorations placed in primary molars with the atraumatic restorative treatment (ART) approach. METHODS: Three dentists placed 419 restorations in 219 children aged 6 through 10 years who had bilateral matched pairs of carious posterior Class I and II primary teeth. They used a split-mouth design to place the two materials, which were assigned randomly to contralateral sides. The authors evaluated the restorations according to U.S. Public Health Service Ryge criteria. RESULTS: After 24 months, 96.7 percent of the Class I GIC restorations and 91 percent of the resin-based composite restorations survived, while the success rates for the Class II restorations were 76.1 percent and 82 percent for the GIC and resin-based composite restorations, respectively. The survival rate of the Class II resin-based composite restorations was 5.9 percent higher than that of the GIC restorations at the 24-month evaluation, but this difference was not statistically significant. However, the study results showed a statistically significant difference in survival rates between Class I and II restorations for both materials. CONCLUSION AND CLINICAL IMPLICATIONS: The two-year clinical performance of both materials was satisfactory for the restoration of Class I and II primary molars using the ART approach.

PMID: 17082278 [PubMed - indexed for MEDLINE]

Minimizing dentinal fluid flow associated with gap formation.

J Dent Res. 2006 Nov;85(11):1027-31

Authors: Ratih DN, Palamara JE, Messer HH

The relationship between gap formation and outward fluid flow and procedures to minimize both phenomena were investigated in extracted human premolars restored in vitro with MOD composite restorations. We hypothesized that either glass-ionomer cement (GIC) liners or low-shrinkage composite could reduce fluid flow related to gap formation. Two groups restored with bonding agents with either high- or low-shrinkage resin composites, and 2 groups restored by either conventional or light-cured GIC liner plus resin composite were compared (8 teeth/group). Fluid flow was measured with an automated apparatus. Baseline fluid flow was low and unchanged after bonding, but increased sharply (though transiently) after teeth were lined with GIC. Outward flow was significantly greater with conventional than with light-cured GIC. Inward fluid flow occurred during light-curing, followed by extensive, prolonged outward flow after curing. Low-shrinkage composite or GIC liners reduced gap formation and limited outward fluid flow. GIC liners promoted outward fluid flow during their setting reactions.

PMID: 17062744 [PubMed - indexed for MEDLINE]

ART and conventional root restorations in elders after 12 months.

J Dent Res. 2006 Oct;85(10):929-32

Authors: Lo EC, Luo Y, Tan HP, Dyson JE, Corbet EF

Successful use of atraumatic restorative treatment (ART) in children has been reported, but little information is available regarding its use in older adults. The hypothesis of this study was that survival rates of root restorations placed by both ART and the conventional technique were similar. Root-surface caries lesions in 103 institutionalized elders in Hong Kong were treated randomly by either: (1) the conventional approach-caries removed by dental burs, and the cavity filled with light-cured resin-modified glass ionomer; or (2) the ART approach-caries removed by hand instruments, and the cavity filled with chemically cured high-strength glass ionomer. In total, 84 conventional and 78 ART restorations were placed. After 12 months, 63 conventional and 59 ART restorations were reviewed, and the respective 12-month survival rates were 91.7% and 87.0% (p > 0.05). It is concluded that the survival rates of both types of root restorations were high and similar.

PMID: 16998134 [PubMed - indexed for MEDLINE]

Surface roughness of glass ionomer cements indicated for atraumatic restorative treatment (ART).

Braz Dent J. 2006;17(2):106-9

Authors: da Silva RC, Zuanon AC

The purpose of this study was to evaluate the surface roughness of four conventional chemically cured glass ionomer cements (Fuji IX, Ketac Molar, Vidrion R and Vitromolar) commonly used in atraumatic restorative treatment (ART) immediately after material preparation. Twenty specimens of each glass ionomer cement were fabricated and surface roughness was measured after material setting. The specimens were further examined under scanning electron microscopy. Data were analyzed statistically by Kruskal-Wallis test and Mann-Whitney test at 5% significance level. Two-by-two comparisons showed statistically significant difference (p<0.05) between all materials, except for Ketac Molar and Vidrion R, which had statically similar results (p>0.05). Regarding their results of surface roughness, the materials can be presented in a crescent order, as follows: Ketac Molar < Vidrion R < Fuji IX < Vitromolar. In conclusion, from the tested glass ionomer cements, Fuji IX, Ketac Molar and Vidrion R presented acceptable surface roughness after setting reaction while Vitromolar showed remarkably higher surface roughness.

PMID: 16924335 [PubMed - indexed for MEDLINE]

Effects of a glass-ionomer cement on the remineralization of occlusal caries--an in situ study.

Braz Oral Res. 2006 Apr-Jun;20(2):91-6

Authors: Amaral MT, Guedes-Pinto AC, Chevitarese O

This work evaluated the remineralization of demineralized enamel of pits and fissures of human third molars sealed with a glass ionomer cement (Fuji IX, GC Corporation--Japan) or with a Bis-GMA sealant (Delton--Dentsply). Ten volunteers participated in this in situ study that consisted of two thirty-day periods using intra-oral devices, with a weeks interval in between. Four experimental treatment procedures and one control were randomly assigned to the volunteers specimens: Group I, no treatment, control; Group II, artificial caries process; Group III, same treatment as Group II, but sealed with Delton (Dentsply); Group IV, same treatment as Group II, but sealed with Fuji IX (GC Corporation--Japan); Group V, same treatment as Group II and no sealing. Groups I and II were not submitted to the oral environment and served as controls. After a period of 30 days in the oral environment, the specimens were removed from the devices, embedded in acrylic resin, ground flat and polished. Then, Knoop hardness tests were performed, with a 25 g static load applied for 15 seconds. The measurements were made from the base of the fissure up to an opening of 600 microm, pre-established between the inclines of the cusps. Three indentations were then made, located at 25, 75, and 125 microm in depth from the outer enamel margin and 100 microm apart from each other (Micromet 2003). The Brieger F and Bonferronis tests were applied to the measurements. It was concluded that sealing with the glass ionomer cement Fuji IX was capable of making the enamel of pits and fissures more resistant by increasing the value of Knoop hardness.

PMID: 16878198 [PubMed - indexed for MEDLINE]

Overcoming the challenges of Class II resin-based composites.

J Am Dent Assoc. 2006 Jul;137(7):1021-3

Authors: Christensen GJ

PMID: 16803830 [PubMed - indexed for MEDLINE]

An in vitro assessment of prefabricated fiber post systems.

J Am Dent Assoc. 2006 Jul;137(7):1006-12

Authors: Teixeira EC, Teixeira FB, Piasick JR, Thompson JY

BACKGROUND: The authors conducted a study to characterize the in vitro retention, fracture and light transmission behavior of four different fiber-reinforced resin-based composite root canal posts. METHODS: The authors divided 44 teeth into four groups according to the type of post they would receive: parallel fiberglass posts, double-tapered fiber quartz posts, tapered fiberglass posts and two different types of parallel fiberglass posts. They prepared teeth and cemented posts with dual-cured resin cement. After the specimens aged, the authors conducted pull-out tests. For fracture testing, they loaded posts at 45 degrees in a universal testing machine. They determined load-to-fracture values and relative stiffness. They measured percentage of light transmission by means of a light microscope coupled with a spectrometer. RESULTS: Both tapered posts showed lower retention than did the parallel posts. Scanning electron microscropic analysis indicated that more cement adhered to the surfaces of the parallel fiberglass post than to those of the tapered fiberglass post. All posts demonstrated some plastic behavior, with the double-tapered fiber quartz post being stiffer than the others. CONCLUSION: Parallel fiber-reinforced composite posts showed better retention than did tapered posts when a dual-cured resin-based cement was used. Translucent prefabricated posts have limited light transmission. CLINICAL IMPLICATIONS: Parallel prefabricated fiber posts luted with dual-cured resin-based cement seem to be suitable for clinical application in endodontically treated teeth that require post-and-core restoration, showing good retention and acceptable fracture resistance.

PMID: 16803828 [PubMed - indexed for MEDLINE]

Survival of ART and amalgam restorations in permanent teeth of children after 6.3 years.

J Dent Res. 2006 Jul;85(7):622-6

Authors: Frencken JE, Taifour D, van 't Hof MA

The null hypothesis tested was that there is no difference in the survival percentages of all restorations placed through the Atraumatic Restorative Treatment (ART) approach, with high-viscosity glass ionomer, and those produced through the traditional approach, with amalgam (TA), in the permanent dentitions of children after 6.3 years. Using a parallel group design, we randomly assigned a total of 370 children, aged 6 to 9 years, to the ART group and 311 children, also aged 6 to 9 years, to the TA group. Eight dentists placed a total of 1117 single- and multiple-surface restorations. The cumulative survival percentages for ART glass-ionomer restorations were statistically significantly higher than those of amalgam restorations at all time intervals except the first (p < or = 0.044). After 6.3 years, the cumulative survival percentages of ART and amalgam restorations were 66.1% (SE = 3.1%) and 57.0% (SE = 3.3%), respectively. We concluded that the restorations produced with the ART approach, with high-viscosity glass ionomer, survived longer than those produced with the traditional approach, with amalgam, in the permanent teeth of young children.

PMID: 16798862 [PubMed - indexed for MEDLINE]

Antibacterial activity of glass-ionomer restorative cements and polyacid modified composite resin against cariogenic bacteria.

Indian J Med Microbiol. 2006 Apr;24(2):150-1

Authors: Menon T, Kumar CP, Dinesh K

PMID: 16687876 [PubMed - indexed for MEDLINE]

Microleakage of restorative materials: an in vitro study.

J Indian Soc Pedod Prev Dent. 2006 Mar;24(1):15-8

Authors: Mali P, Deshpande S, Singh A

The present study was conducted with the aim of evaluating and comparing the microleakage of glass ionomer, composite resin and compomers. Class V cavities were made in thirty intact caries free premolars and restored with restorative materials to be tested respectively. The teeth were thermocycled and subjected to silver nitrate dye penetration. They were subsequently sectioned buccolingually. Microleakage was evaluated under a stereomicroscope and data subjected to statistical analysis. The study concluded that microleakage was evident in all restorative materials, with glass ionomer showing maximum leakage followed by composite resin. Compomer demonstrated the best results with minimum leakage.

PMID: 16582525 [PubMed - indexed for MEDLINE]

Development of a self-etch adhesive for resin-modified glass ionomers.

J Dent Res. 2006 Apr;85(4):349-53

Authors: Coutinho E, Van Landuyt K, De Munck J, Poitevin A, Yoshida Y, Inoue S, Peumans M, Suzuki K, Lambrechts P, Van Meerbeek B

The favorable self-adhesiveness of resin-modified glass ionomers (RMGIs) might be even further improved if the time-consuming and technically sensitive etch-and-rinse pre-treatment step with polyalkenoic acids could be avoided. We undertook this study to assess the effectiveness of an experimental self-etch adhesive for RMGIs that does not need to be rinsed off. Ultrastructural analysis and micro-tensile bond strength testing to enamel and dentin of a RMGI restorative material and a RMGI adhesive were performed after 4 different surface pre-treatments: no conditioning; 25% polyalkenoic acid; an experimental self-etch adhesive; and 37.5% phosphoric acid followed by the experimental self-etch adhesive. The use of an experimental self-etch adhesive increased the bond strength of RMGIs, especially after an additional conditioning step. Interfacial analysis showed the formation of a thin hydroxyapatite-containing hybrid layer. The self-etch technique enhances the user-friendliness of RMGIs and lowers their technique-sensitivity, while maintaining desirable characteristics of the conventional etch-and-rinse approach with polyalkenoic acids.

PMID: 16567557 [PubMed - indexed for MEDLINE]

A one-year clinical evaluation of a high-viscosity glass ionomer cement in primary molars.

J Contemp Dent Pract. 2006 Feb 15;7(1):71-8

Authors: Yilmaz Y, Eyuboglu O, Kocogullari ME, Belduz N

In this study one-year clinical results of high-viscosity glass ionomer cement (GIC) (Fuji IX, A3, GC, Japan) were determined in class I and class II restorations in 68 primary molars with occlusal or approximal caries. Following caries removal and cavity preparation, the teeth were restored with Fuji IX. The restorations were evaluated according to the U.S. Public Health Service's (USPHS) criteria at the end of one year. Statistical analyses of the data obtained were analyzed using the X2 test. The evaluations showed no statistically significant difference between class I and class II restorations in terms of the color mismatch, anatomic form, marginal adaptation, and secondary caries (P>0.05), but they were statistically significant with regard to cavosurface marginal discoloration (P<0.05). At the end of one year, the success rate of the class I and class II restorations of the primary molars restored with Fuji IX was 94%.

PMID: 16491149 [PubMed - indexed for MEDLINE]

Early biofilm formation and the effects of antimicrobial agents on orthodontic bonding materials in a parallel plate flow chamber.

Eur J Orthod. 2006 Feb;28(1):1-7

Authors: Chin MY, Busscher HJ, Evans R, Noar J, Pratten J

Decalcification is a commonly recognized complication of orthodontic treatment with fixed appliances. A technology, based on a parallel plate flow chamber, was developed to investigate early biofilm formation of a strain of Streptococcus sanguis on the surface of four orthodontic bonding materials: glass ionomer cement (Ketac Cem), resin-modified glass ionomer cement (Fuji Ortho LC), chemically-cured composite resin (Concise) and light-cured composite resin (Transbond XT). S. sanguis was used as it is one of the primary colonizers of dental hard surfaces. Artificial saliva was supplied as a source of nutrients for the biofilms. The effects of two commercially available mouthrinses (i.e. a fluoride containing rinse and chlorhexidine) were evaluated. Initial colonization of the bacterium was assessed after 6 hours of growth by the percentage surface coverage (PSC) of the biofilm on the disc surfaces. There were statistically significant differences in bacterial accumulation between different bonding materials (P < 0.05), Concise being the least colonized and Transbond XT being the most colonized by S. sanguis biofilms. All materials pre-treated with 0.05 per cent sodium fluoride mouthrinse showed more than 50 per cent reduction in biofilm formation. The 0.2 per cent chlorhexidine gluconate mouthrinse caused significant reduction of biofilm formation on all materials except Ketac Cem. This in vitro study showed that the use of a chemically-cured composite resin (Concise) reduced early S. sanguis biofilm formation. Also, fluoride had a greater effect in reducing the PSC by S. sanguis biofilms than chlorhexidine. Rinsing with 0.05 per cent sodium fluoride prior to placement of orthodontic appliances is effective in reducing early biofilm formation.

PMID: 16373451 [PubMed - indexed for MEDLINE]

The two-year clinical performance of esthetic restorative materials in noncarious cervical lesions.

J Am Dent Assoc. 2005 Nov;136(11):1547-55

Authors: Onal B, Pamir T

BACKGROUND: Materials used in restoration of cervical lesions include resin-modified glass ionomer cements, polyacid-modified resin-based composites and resin-based composites. In this study, the authors evaluated the clinical performance of these materials over a two-year period. METHODS: Thirty patients were enrolled in this study. The authors placed in these patients 130 restorations, 24 of which were Vitremer (3M Dental Products, St. Paul, Minn.), 38 were F2000 Compomer (3M Dental Products), 46 were Dyract AP (Dentsply DeTrey, Konstanz, Germany) and 22 were Valux Plus (3M Dental Products). Enamel margins were not beveled, and no mechanical retention was placed. Two independent, calibrated examiners evaluated the restorations baseline and at one and two years after placement using modified U.S. Public Health Service criteria. RESULTS: Retention rates at the end of two years were 100 percent for Vitremer, 67 percent for F2000 Compomer, 68 percent for Dyract AP and 70 percent for Valux Plus. The retention rate of Vitremer was significantly higher than that of the others (P < .05). In other categories, however, Valux Plus had the most favorable performance (P < .05). No secondary caries was detected around any restoration. CONCLUSION: Vitremer, with its high retention rate, seems to be the most appropriate material for restoration of noncarious cervical lesions, though it does not have the esthetic properties of resin-based composites. All materials used in this study were in need of improvements. CLINICAL IMPLICATIONS: Resin-modified glass ionomer cement, polyacid-modified resin-based composite and resin-based composite behaved differently in the restoration of noncarious cervical lesions. Therefore, clinicians should take factors such as esthetic needs and localization into account in selecting materials for such restorations.

PMID: 16329418 [PubMed - indexed for MEDLINE]

Effectiveness of 4 pulpotomy techniques--randomized controlled trial.

J Dent Res. 2005 Dec;84(12):1144-8

Authors: Huth KC, Paschos E, Hajek-Al-Khatar N, Hollweck R, Crispin A, Hickel R, Folwaczny M

Pulpotomy is the accepted therapy for the management of cariously exposed pulps in symptom-free primary molars; however, evidence is lacking about the most appropriate technique. The aim of this study was to compare the relative effectiveness of the Er:YAG laser, calcium hydroxide, and ferric sulfate techniques with that of dilute formocresol in retaining such molars symptom-free. Two hundred primary molars in 107 healthy children were included and randomly allocated to one of the techniques. The treated teeth were blindly re-evaluated after 6, 12, 18, and 24 months. Descriptive data analysis and logistic regression analysis, accounting for each patient's effect by a generalized estimating equation (GEE), were used. After 24 months, the following total and clinical success rates were determined (%): formocresol 85 (96), laser 78 (93), calcium hydroxide 53 (87), and ferric sulfate 86 (100). Only calcium hydroxide performed significantly worse than formocresol (p = 0.001, odds ratio = 5.6, 95% confidence interval 2.0-15.5). In conclusion, calcium hydroxide is less appropriate for pulpotomies than is formocresol.

PMID: 16304444 [PubMed - indexed for MEDLINE]

Retention of maxillary molars with Class III furcation involvement utilizing glass-ionomer: two case reports.

J Contemp Dent Pract. 2005 Nov 15;6(4):160-7

Authors: Reddy KP, Nayak DG, Uppoor AS

Advanced furcation invasion has long been a treatment dilemma for the clinician. The present two case reports used a glass ionomer restorative material as a barrier in the treatment of maxillary Class III furcation defects. One year follow-up results showed a reduction in tooth mobility and probing depths and no bleeding on probing with the use of the glass ionomer. These case reports offer another option in the treatment of a seemingly hopeless periodontally involved maxillary molar.

PMID: 16299618 [PubMed - indexed for MEDLINE]

The color differences between different thicknesses of resin veneered over amalgam.

J Contemp Dent Pract. 2005 Nov 15;6(4):38-45

Authors: Al-Jazairy YH, El-Hejazi AA

STATEMENT OF PROBLEM: Composites and compomers are popular in dental practice. However, little is known about their esthetic appearance as veneering restorative materials over amalgam restorations. PURPOSE: This in vitro study was designed to assess the color differences of composite and compomer restorative materials, placed in thicknesses of 1 mm and 2 mm over amalgam. MATERIAL AND METHODS: Thirty six cylindrical Teflon molds were filled with amalgam (13 mm diameter, 2 mm thickness) and stored at 37 degrees C and 100% relative humidity for 7 days. Nine veneers (for each thickness of 1 and 2 mm) were fabricated from four types of tooth-colored restorative material, Dyract AP (DYR), Compoglass F (COMP), Herculite XRV (XRV), and Vitalecense (VIT), over amalgam specimens using Teflon-split molds and following the manufacturers' instructions. A spectrophotometer was used to measure the color difference DeltaE* between the two thicknesses. RESULTS: Color difference DeltaE* values for 1 mm thickness veneers [XRV (2.52), Comp (5.46), VIT (6.73), and DYR (6.88)] were statistically significantly higher than the 2 mm thickness [XRV (1.32), Comp (3.24), VIT (4.89), and DYR (4.83)]. Although the XRV material had the lowest DeltaE* values, no statistically significant difference was found between the two thicknesses. The color measurements at L*, a*, and b* showed most materials became darker in color at either thickness. CONCLUSION: The thicker veneer specimens were found to be closer in color to the controls than the thinner specimens. Only XRV had color differences (DeltaE*) small enough to be considered clinically acceptable (2.52 and 1.32 at 1 mm and 2 mm, respectively). CLINICAL IMPLICATIONS: In this in vitro study the color of XRV was affected the least when veneered on amalgam. Opaquers may be needed to be used with thinner veneers to minimize the effect of amalgam background.

PMID: 16299605 [PubMed - indexed for MEDLINE]

In vitro activity of zinc oxide-eugenol and glass ionomer cements on Candida albicans.

Braz Oral Res. 2005 Apr-Jun;19(2):134-8

Authors: Cassanho AC, Fernandes AM, Oliveira LD, Carvalho CA, Jorge AO, Koga-Ito CY

The aim of this study was to evaluate in vitro the antimicrobial activity of glass ionomer (GIC) and zinc oxide-eugenol (ZOE) cements against Candida albicans. Standardized GIC and ZOE specimens were maintained in contact with C. albicans suspension (1 x 10(6) cells/ml) at 37 degrees C for 24 h, 48 h or 7 days. A control group without any testing cement was included. After the incubation period, aliquots of 0.1 ml were plated on Sabouraud's agar, and then the number of colonies was counted. The results were expressed as values of logarithms of colony-forming units per milliliter (log CFU/mL) and were analyzed statistically by Kruskal-Wallis ANOVA. After 48 h of incubation, the ZOE group presented no growth of C. albicans. GIC and control groups presented similar mean values at all tested periods. According to the results obtained, it could be concluded that, under the experimental conditions, ZOE cement was more effective in vitro against C. albicans than GIC.

PMID: 16292447 [PubMed - indexed for MEDLINE]

An investigation into the bonding of orthodontic attachments to porcelain.

Eur J Orthod. 2006 Feb;28(1):74-7

Authors: Larmour CJ, Bateman G, Stirrups DR

This study assessed bonding of orthodontic brackets to porcelain teeth using two different surface preparation techniques and comparing two bonding systems, Fuji Ortho L.C. and Transbond. Four groups of 20 porcelain premolar teeth were bonded with metal orthodontic brackets (0.022 inch Minitwin, 3M Unitek) according to the following protocol: Transbond with a phosphoric acid etch (group 1), Transbond with a hydrofluoric acid etch (group 2), Fuji Ortho L.C. with a hydrofluoric acid etch (group 3), and Fuji Ortho L.C. with a phosphoric acid etch (group 4). All groups were bonded with a silane coupling agent. The teeth were debonded with an Instron universal testing machine. Bond strength, site of bond failure and adhesive remnant index (ARI) were recorded for each group. Differences between groups were analysed statistically. The composite resin groups (groups 1 and 2) had the highest mean bond strength values at 7.9 and 9.7 MPa, respectively. The resin-modified glass ionomer cement groups (RMGIC; groups 3 and 4) had the lowest mean bond strength values at 6.3 and 1.8 MPa, respectively. The mean bond strength of group 3 was significantly lower than all other groups (P < 0.0001). The Fuji groups had also significantly (P < 0.001) lower ARI scores than the composite groups (groups 1 and 2). Most samples experienced porcelain surface damage, except group 4. In conclusion, the highest bond strength levels were achieved with a conventional composite resin cement (groups 1 and 2). No significant differences in bond strength were found between the hydrofluoric and phosphoric acid etch technique.

PMID: 16199411 [PubMed - indexed for MEDLINE]

Microleakage on Class V glass ionomer restorations after cavity preparation with aluminum oxide air abrasion.

Braz Dent J. 2005;16(1):35-8

Authors: Corona SA, Borsatto MC, Rocha RA, Palma-Dibb RG

This in vitro study assessed the marginal microleakage on class V cavities prepared with aluminum oxide air abrasion and restored with different glass ionomer cements. The cavities were prepared on the buccal and lingual surfaces of 15 sound third molars with an air- abrasion device (Kreativ Mach 4.1; New Image) using a 27.5-microm aluminum oxide particle stream, and were assigned to 3 groups of 10 cavities each. The restorative materials were: group I, a conventional glass ionomer cement (Ketac-Fil); groups II and III, resin-modified glass ionomer cements (Vitremer R and Fuji II LC, respectively). After placement of the restorations, the teeth were stored in distilled water at 37 degrees C for 24 h, polished and then submitted to a thermocycling regimen of 500 cycles, isolated, immersed in 0.2% Rhodamine B solution for 24 h, included and serially sectioned. Microleakage was assessed by viewing the specimens under an optical microscope connected to a color video camera and a computer. The images obtained were digitized and analyzed for microleakage using software that allows for a standard quantitative assessment of dye penetration in millimeters. Statistical analysis was done using the Kruskall-Wallis and Wilcoxon tests. Means of dye penetration (%) were: occlusal - I: 25.76 +/- 34.35, II: 20.00 +/- 42.16, III: 28.25 +/- 41.67; cervical - I: 23.72 +/- 41.84; II: 44.22 +/- 49.69, III: 39.27 +/- 50.74. No statistically significant differences (p>0.05) were observed among either the glass ionomer cements or the margins. In conclusion, class V cavities restored with either conventional or resin-modified glass ionomer cements after preparation with aluminum oxide air abrasion did not show complete sealing at the enamel and dentin/cementum margins.

PMID: 16113931 [PubMed - indexed for MEDLINE]

The influence of accelerating the setting rate by ultrasound or heat on the bond strength of glass ionomers used as orthodontic bracket cements.

Eur J Orthod. 2005 Oct;27(5):472-6

Authors: Algera TJ, Kleverlaan CJ, de Gee AJ, Prahl-Andersen B, Feilzer AJ

Conventional glass ionomer cements (GICs) may be a viable option for bracket bonding when the major disadvantages of these materials, such as the slow setting reaction and the weak initial bond strength, are solved. The aim of this in vitro study was to investigate the influence of ultrasound and heat application on the setting reaction of GICs, and to determine the tensile force to debond the brackets from the enamel. A conventional fast-setting GIC, Fuji IX Fast, and two resin-modified glass ionomer cements (RMGICs), Fuji Ortho LC and Fuji Plus, were investigated. Three modes of curing were performed (n = 10): (1) according to the manufacturer's prescription, (2) with 60 seconds application of heat, or (3) with 60 seconds application of ultrasound. The tensile force required to debond the brackets was determined as the tension 15 minutes after the start of the bonding procedure. The mode of failure was scored according to the Adhesive Remnant Index (ARI) to establish the relative amount of cement remnants on the enamel surface. Curing with heat and ultrasound shortened the setting reaction and significantly (P < 0.05) increased the bond strength to enamel. The ARI scores showed an increase for all materials after heat and ultrasound compared with the standard curing method, most notably after heat application.

PMID: 16049039 [PubMed - indexed for MEDLINE]

An in vitro comparison of the shear bond strength of a resin-reinforced glass ionomer cement and a composite adhesive for bonding orthodontic brackets.

Eur J Orthod. 2005 Oct;27(5):477-83

Authors: Movahhed HZ, Ogaard B, Syverud M

The shear bond strength (SBS) of a light-cured, resin-reinforced glass ionomer and a composite adhesive in combination with a self-etching primer was compared after different setting times to evaluate when orthodontic wires could be placed. Additionally, the fracture site after debonding was assessed using the Adhesive Remnant Index (ARI). Eighty freshly extracted human premolars were used. Twenty teeth were randomly assigned to each of four groups: (1) brackets bonded with Transbond XT with a Transbond Plus etching primer and debonded within 5 minutes; (2) brackets bonded with Fuji Ortho LC and debonded within 5 minutes; (3) brackets bonded as for group 1 and debonded within 15 minutes; (4) brackets bonded as for group 2 and debonded within 15 minutes. The SBS of each sample was determined with an Instron machine. The mean SBS were, respectively: (1) 8.8 +/- 2 MPa; (2) 6.6 +/- 2.5 MPa; (3) 11 +/- 1.6 MPa and (4) 9.6 +/- 1.6 MPa. Interpolating the cumulative fracture probability by means of a Weibull analysis, the 10 per cent probabilities of fracture for the groups were found to be attained for shear stresses of 6.1, 3.1, 8.3 and 7.1 MPa, respectively. Chi-square testing of the ARI scores revealed that the nature of the remnant did not vary significantly with time, but the type of bonding material could generally be distinguished in leaving more or less than 10 per cent of bonding material on the tooth. After debonding, the Transbond system was likely to leave adhesive on at least 10 per cent of the bonded area of the tooth. The present findings indicate that brackets bonded with either Transbond XT in combination with Transbond Plus etching primer and Fuji Ortho LC had adequate bond strength at 5 minutes and were even stronger 15 minutes after initial bonding.

PMID: 16043469 [PubMed - indexed for MEDLINE]

[The effects of occlusal adjustment on retention of dental wedge-shaped defect]

Shanghai Kou Qiang Yi Xue. 2005 Jun;14(3):323-4

Authors: Zhu TJ

To observe the retention of filling material for dental wedge-shaped defects after occlusal adjustment, patients in the experimental group was given suitable occlusal adjustment before filling with glass ionomer cements or light-curing composite resin according to the patient's requirements. Evaluation was carried out by statistical analysis after one year. The results showed significant difference in the retention between the experimental group and the control group (P<0.01) after one year. It's concluded that suitable occlusal adjustment of the teeth with wedge-shaped defect is beneficial to the retention of filling material.

PMID: 15995787 [PubMed - in process]

Fluorides, orthodontics and demineralization: a systematic review.

J Orthod. 2005 Jun;32(2):102-14

Authors: Benson PE, Shah AA, Millett DT, Dyer F, Parkin N, Vine RS

OBJECTIVES: To evaluate the effectiveness of fluoride in preventing white spot lesion (WSL) demineralization during orthodontic treatment and compare all modes of fluoride delivery. DATA SOURCES: The search strategy for the review was carried out according to the standard Cochrane systematic review methodology. The following databases were searched for RCTs or CCTs: Cochrane Clinical Trials Register, Cochrane Oral Health Group Specialized Trials Register, MEDLINE and EMBASE. Inclusion and exclusion criteria were applied when considering studies to be included. Authors of trials were contacted for further data. DATA SELECTION: The primary outcome of the review was the presence or absence of WSL by patient at the end of treatment. Secondary outcomes included any quantitative assessment of enamel mineral loss or lesion depth. DATA EXTRACTION: Six reviewers independently, in duplicate, extracted data, including an assessment of the methodological quality of each trial. DATA SYNTHESIS: Fifteen trials provided data for this review, although none fulfilled all the methodological quality assessment criteria. One study found that a daily NaF mouthrinse reduced the severity of demineralization surrounding an orthodontic appliance (lesion depth difference -70.0 microm; 95% CI -118.2 to -21.8 microm). One study found that use of a glass ionomer cement (GIC) for bracket bonding reduced the prevalence of WSL (Peto OR 0.35; 95% CI 0.15-0.84) compared with a composite resin. None of the studies fulfilled all of the methodological quality assessment criteria. CONCLUSIONS: There is some evidence that the use of a daily NaF mouthrinse or a GIC for bonding brackets might reduce the occurrence and severity of WSL during orthodontic treatment. More high quality, clinical research is required into the different modes of delivering fluoride to the orthodontic patient.

PMID: 15994984 [PubMed - indexed for MEDLINE]

An investigation into the use of two polyacid-modified composite resins (compomers) and a resin-modified glass poly(alkenoate) cement used to retain orthodontic bands.

Eur J Orthod. 2005 Jun;27(3):245-51

Authors: Williams PH, Sherriff M, Ireland AJ

The aim of this investigation was to determine the effectiveness of a conventional glass poly(alkenoate) cement (Intact) and newer polyacid-modified composite resin cements (Transbond Plus and Ultra Band-Lok) to retain orthodontic bands.In the in vitro part of this study, stainless steel bands were cemented to 240 extracted third molar teeth in three test groups comprising Intact, Transbond Plus and Ultra Band-Lok. The force to deband (N) for all three cements was recorded using an Instron universal testing machine after the following observation periods: 20 minutes and 3, 6 and 12 months. The results indicated that all three cements increased their median force to deband after 12 months. Of the two compomers, Transbondtrade mark Plus demonstrated the highest median force to deband at all four time intervals.In the in vivo part of the study, 30 patients participated in a randomized cross-mouth clinical trial where the molar bands were cemented in place using either Intact or Transbond Plus. Ultra Band-Lok was not used in the clinical part of the study. The results showed there to be no clinically significant difference in band failure rates between the two cements. When patients were asked to score each for taste, there was a significant difference, with the glass poly(alkenoate) cement (Intact) being more acceptable than the polyacid-modified composite Transbond Plus (P < 0.001).No significant differences were observed in the in vitro median force to deband or in vivo band failure rates between the glass poly(alkenoate) cement and the polyacid-modified composite resins. The choice of cementing agent can therefore be made on patient factors, e.g. taste, or operator factors, e.g. ease of handling, cost and shelf life.

PMID: 15947223 [PubMed - indexed for MEDLINE]

The weight change of various light-cured restorative materials stored in water.

J Contemp Dent Pract. 2005 May 15;6(2):72-9

Authors: Keyf F, Yal&#xE7;in F

This study investigated weight changes of seven different light-cured composite restorative materials, one polyacid glass ionomer compomer, and one light-cured glass-ionomer cement following short-term and long-term storage in water. Two packable composites, three universal (hybrid) composites, one microglass composite, one polyacid glass ionomer resin composite (compomer), one microhybrid low-viscosity (flowable) composite, and one light cured glass ionomer composite cement were evaluated in this study. The weight changes of these specimens were measured daily (short-term storage), and they were measured after six weeks (long-term storage) using an electronic analytical balance. A significant difference was found in Ionoliner, Dyract AP, Opticor flow, Charisma, and Solitare 2, but no significant difference was found in the others (Filtek Z 250, Filtek P60, TPH Spectrum, and Valux Plus). Weight change showed a tendency to increase with the time of water storage. The greatest weight change occurred in light-cured glass ionomer composite cement (Ionoliner), which is followed in order by the weight changes in Dyract AP, Opticor Flow, Charisma, Solitare 2, Filtek Z250, Filtek P60, TPH Spectrum; Valux Plus had the least amount of change.

PMID: 15915206 [PubMed - indexed for MEDLINE]

The effect of bleaching agents on the surface hardness of tooth colored restorative materials.

J Contemp Dent Pract. 2005 May 15;6(2):18-26

Authors: Taher NM

AIM OF THE STUDY: The aim of this study was to evaluate the effect of at-home (Opalesence/Dr. kit 15%, Ultradent, Products, Inc. South Jordan, UT, USA) and in-office (Superoxol 35%, Sultan Chemists, Inc., Englewood, NJ, USA) bleaching on the surface hardness of the following tooth colored restorative materials: composite resin, Point-4 (P4), Kerr Corporation, Orange, CA, USA; ormocer, Admira (AD),VOCO, Germany; compomer Dyract AP (DY), Dentsply DeTrey GmbH, Germany; and resin modified glass ionomer cement, Fuji II LC (FL), GC Corporation, Japan. METHODOLOGY: Sixty specimens were prepared; 15 specimens of each material (each group n = 5, control after 15 days, at-home and in-office). All specimens were stored in distilled water at room temperature for 24 hrs before testing. A universal testing machine (Micromet 2100 series micro hardness testers) was used for testing Vicker's surface hardness for the three groups for every tested material. All results were statistically analyzed with one way analysis of variance (ANOVA), Post hoc Tukey HSD tests (P < 0.05), and percentage changes for Tukey. RESULTS: All the tested materials showed an increase in Vicker's surface hardness between base line (24 hrs) and the control group after 15 days storage in distilled water except DY which showed a decrease in surface hardness. All tested materials showed a decrease in surface hardness from control group after 15 days and both at-home and in-office bleaching agents except DY which showed increased values. SIGNIFICANCE: At-home as well as in-office bleaching agents have a softening effect on some tooth colored restorative material, and the patient must be aware before using them.

PMID: 15915201 [PubMed - indexed for MEDLINE]

Fluoride-releasing capacity and cariostatic effect provided by sealants.

J Oral Sci. 2005 Mar;47(1):35-41

Authors: Lobo MM, Pecharki GD, Tengan C, da Silva DD, da Tagliaferro EP, Napimoga MH

This study evaluated the effect of sealants on enamel demineralization, focusing on physical protection of the sealed enamel and fluoride protection of the adjacent unsealed enamel. Occlusal fissures with areas measuring 12 mm2 were delimited in 48 extracted molars, randomly divided into 4 groups (n =12): 1) no sealing; 2) sealing with a resin-modified glass-ionomer (Vitremer, 3M ESPE); 3) sealing with a fluoride-releasing composite sealant (Clinpro Sealant, 3M ESPE); and 4) sealing with a non-fluoridated composite sealant (Concise, 3M ESPE). A 4-mm2 window was outlined on the buccal enamel for analysis of fluoride uptake. Following treatment, groups 2, 3 and 4 were subjected to 5-days of pH-cycling, while group 1 was kept in a moist environment at 37 degrees C. Fluoride uptake was assessed by dental biopsy, and the amount of fluoride released to the cycling solutions was determined by ion analysis. Enamel demineralization around the sealants was evaluated by cross-sectional micro-hardness analysis. Group 2 showed higher levels of fluoride release (P < 0.01) and uptake by enamel (P < 0.05), and lower levels of demineralization (P < 0.05) than groups 3 and 4. Group 3 exhibited reduced demineralization on unsealed enamel and provided fluoride uptake in a distant enamel area, while group 4 did not.

PMID: 15881227 [PubMed - indexed for MEDLINE]

Influence of temporary cement remnant and surface cleaning method on bond strength to dentin of a composite luting system.

J Oral Sci. 2005 Mar;47(1):9-13

Authors: Kanakuri K, Kawamoto Y, Matsumura H

The aim of the current study was to evaluate the influence of polycarboxylate temporary cement remaining on the dentin surface on the bond strength of a composite luting system. An acrylic resin plate was luted to bovine dentin with a polycarboxylate temporary cement (HY-Bond Temporary Cement Hard, HYB). The temporary cement was not used for the control groups. After removing the temporary cement with an excavator, dentin specimens were divided into five groups; 1) no subsequent treatment, 2) cleaning with a rotational brush (RTB), 3) cleaning with a rotational brush and non-fluoridated flour of pumice, 4) sweeping with an air scaler, and 5) treated with a sonic toothbrush. A silane-treated ceramic disk (IPS Empress) was bonded to each dentin specimen with a composite luting system (Panavia F). Shear testing results showed that the RTB groups exhibited the highest bond strength regardless of the use of temporary cement (P < 0.05). The use of a rotational brush with water coolant is recommended to achieve ideal bond strength between the Panavia F luting system and dentin to which HYB temporary cement was primarily applied.

PMID: 15881223 [PubMed - indexed for MEDLINE]

Chlorhexidine-modified glass ionomer for band cementation? An in vitro study.

J Orthod. 2005 Mar;32(1):26

Authors: Ireland T

PMID: 15816073 [PubMed - indexed for MEDLINE]

Chlorhexidine-modified glass ionomer for band cementation? An in vitro study.

J Orthod. 2005 Mar;32(1):36-42

Authors: Millett DT, Doubleday B, Alatsaris M, Love J, Wood D, Luther F, Devine D

OBJECTIVE: To compare the mean retentive strength, predominant site of band failure, amount of cement remaining on the tooth at deband and survival time of orthodontic micro-etched bands cemented with chlorhexidine-modified (CHXGIC) or conventional glass ionomer cement (GIC). DESIGN: In vitro study. SETTING: Dental Materials Laboratory. MATERIALS AND METHODS: One-hundred-and-twenty intact, caries-free third molars were collected from patients attending for third molar surgery. These were stored for 3 months in distilled water and decontaminated in 0.5% chloramine. To assess retentive strength, 80 teeth were randomly selected and 40 were banded with each cement. Testing was undertaken using a Nene M3000 testing machine at a cross-head speed of 1 mm/min. Following debanding, the predominant site of failure was recorded as cement-enamel or cement-band interface. The amount of cement remaining on the tooth surface following deband was assessed and coded. Survival time for another 40 banded specimens, 20 cemented with each cement, was assessed following application of mechanical stress in a ball mill. MAIN OUTCOME MEASURES: Retentive strength, predominant site of failure, amount of cement remaining on the tooth surface, survival time. RESULTS: Mean retentive strength for bands cemented with CHXGIC (0.32 MPa, SD 0.09) or GIC (0.28 MPa, SD 0.07) did not differ significantly (p=0.05). All bands failed at the enamel-cement interface. There was no significant difference in the amount of cement remaining on the tooth surface after deband for each cement type (p=0.23). The mean survival time of bands cemented with CHXGIC or GIC was 7.0 and 6.4 hours, respectively (p=0.23). CONCLUSIONS: There was no significant difference in mean retentive strength, amount of cement remaining on the tooth after deband or mean survival time of bands cemented with CHXGIC or GIC. Bands cemented with either cement failed predominantly at the enamel-cement interface. The results suggest that CHXGIC may have comparable clinical performance to GIC for band cementation.

PMID: 15784942 [PubMed - indexed for MEDLINE]

Comparison of short-term in vitro fluoride release and recharge from four different types of pit-and-fissure sealants.

Bull Tokyo Dent Coll. 2004 Aug;45(3):173-9

Authors: Koga H, Kameyama A, Matsukubo T, Hirai Y, Takaesu Y

OBJECTIVE: The purpose of this in vitro study was to assess the effects of four commercial fluoride-containing pit-and-fissure sealants on caries prevention. MATERIALS AND METHODS: Four sealants containing fluoride, Fuji III, Fuji III LC (GC Co., Tokyo), Teethmate F-1 (Kuraray Medical Co., Osaka) and Helioseal F (Vivadent Co., Liechtenstein) were used to investigate fluoride release and recharge. Disk-shaped specimens prepared from each material were immersed in distilled water at a temperature of 37 degrees C. After seven days, acidulated phosphate fluoride solution (APF) was applied to each specimen, and it was then again immersed in distilled water for 14 days. We then determined how much fluoride had been released into the immersing water. Fuji III LC was used with APF solution to investigate the fluoride uptake. RESULTS: Fuji III had the highest fluoride release, and Fuji III LC had the highest fluoride recharge. Helioseal F and Teethmate F-1 had almost no fluoride recharge. Fuji III LC/APF had a higher fluoride uptake to enamel than Fuji III LC. CONCLUSIONS: These results suggest that GIC-sealants in the oral cavity can serve as a fluoride reservoir and contribute to retaining a low fluoride level in oral fluids, thereby preventing caries.

PMID: 15779460 [PubMed - indexed for MEDLINE]

Evaluation of intracanal post removal using ultrasound.

Braz Dent J. 2004;15(2):119-26

Authors: Silva MR, Biffi JC, Mota AS, Fernandes Neto AJ, Neves FD

The aim of this study was to determine the effect of ultrasonic vibration on the force necessary to remove pre-fabricated and anatomic and cast posts. Two hundred and forty teeth were divided into two groups. In group I, a 0.8-mm metallic pre-fabricated post, Unimetric-Maillefer, was utilized; in group II, cast copper-aluminum alloy posts measuring 0.8, 1.0 and 1.2 mm in diameter were used. The root canals were prepared in three different diameters: 0.8, 1.0 and 1.2 mm, with a length of 10 mm. The posts were cemented with glass ionomer cement resulting in 20 specimens for each subgroup. Half of the sample was submitted to ultrasonic vibration for 3 min, while the other half did not receive any vibration. The specimens were submitted to traction in a universal testing machine. The results were analyzed by non-parametric Mann-Whitney U, Wilcoxon and Kruskal-Wallis tests. The application of ultrasonic vibration significantly reduced the retention provided by the glass ionomer cement in the fixation of intracanal posts. The ultrasonic action was effective in both pre-fabricated and anatomic and cast posts. The effectiveness of the ultrasonic vibration was not related to the cementation line or the diameter of the post.

PMID: 15776194 [PubMed - indexed for MEDLINE]

Success of an alternative for interim management of irreversible pulpitis.

J Am Dent Assoc. 2004 Dec;135(12):1707-12

Authors: McDougal RA, Delano EO, Caplan D, Sigurdsson A, Trope M

BACKGROUND: Extraction and endodontic therapy are treatment options for irreversible pulpitis. Extraction often is chosen for financial reasons. The authors conducted a study to investigate an alternative interim therapy. METHODS: The authors recruited patients (N = 73) with irreversible pulpitis and whose teeth were restorable but who opted for extraction owing to financial reasons. After undergoing pulpotomy, the teeth were restored by random assignment with one of two intermediate restorative materials: Caulk IRM (Dentsply Caulk, Milford, Del.) (Group I, n = 38) or an IRM base with glass ionomer core (Fuji IX GP, GC America, Alsip, Ill.) (Group II, n = 35). The authors monitored the teeth over six and 12 months for pain, integrity of restoration and radiographic periapical status by densitometric analysis. RESULTS: By six months, 10 percent of subjects remaining in the study (Group I, n = 27; Group II, n = 25) reported pain; by 12 months, 22 percent (Group I, n = 22; Group II, n = 18) reported pain. A two-tailed Fisher exact test showed no significant difference (P > or = .05) between groups at either time interval. No apical radiographic change was noted in 49 percent of teeth at six months (Group I, n = 18; Group II, n = 19) and 42 percent at 12 months (Group I, n = 16; Group II, n = 15). Chi2 analysis demonstrated no significant differences (P > or = .05) between groups. Seven of 22 restorations in Group I and four of 18 in Group II required repair at 12 months with no statistical difference (chi2 analysis, P > or = .05). CONCLUSIONS: The interim treatment of eugenol pulpotomy using either restorative material reliably prevented pain for six months. For longer periods, both restorations may require repair. CLINICAL IMPLICATIONS: This option should preserve the integrity of the arch and extend the use of the tooth while the patient finds the means to finance complete endodontic treatment.

PMID: 15646604 [PubMed - indexed for MEDLINE]

An ex vivo evaluation of resin-modified glass polyalkenoates and polyacid-modified composite resins as orthodontic band cements.

J Orthod. 2004 Dec;31(4):323-8; discussion 301-2

Authors: Knox J, Chye KY, Durning P

OBJECTIVES: The objective of this ex vivo study was to assess the use of resin-modified glass polyalkenoates and polyacid-modified composite resins, as orthodontic band cements. MATERIALS AND METHOD: Plain stainless steel bands were cemented to 350 human extracted third molar teeth using 1 of 7 different cements. Following complete cement cure, half of each sample group was exposed to mechanical stress in a ball mill. Stressed and unstressed samples were tested in tension and the stress at which initial cement failure recorded. The mode of failure was recorded using an adhesive remnant evaluation. RESULTS: The mean band retention stresses offered by the cements studied ranged from 0.96 to 1.56 MPa. Fuji Ortho provided the highest mean band retention stress in "stressed" (1.56 MPa) and "unstressed" (1.45 MPa) states. Exposure to mechanical stress did not appear to significantly influence band retention or mode of cement failure for most cements. Fuji Ortho cement recorded the highest Weibull modulus for all cements tested. Virtually all samples failed at either the cement/enamel or cement band interface. CONCLUSIONS: Significant differences in band displacement stress values and mode of failure were demonstrated between the cements studied. However, generic comparisons were difficult to make.

PMID: 15608348 [PubMed - indexed for MEDLINE]

Surface hardness properties of resin-modified glass ionomer cements and polyacid-modified composite resins.

J Contemp Dent Pract. 2004 Nov 15;5(4):42-9

Authors: Bayindir YZ, Yildiz M

In this study the top and bottom surface hardness of two polyacid-modified composite resins (PMCRs), one resin-modified glass ionomer cement (RMGIC), and one composite resin were evaluated. The affect of water storage on their hardness was also investigated. The study was conducted using four different groups, each having five specimens obtained from fiberglass die molds with a diameter of 5 mm and a height of 2 mm. Measurements were made on the top and bottom surface of each specimen and recorded after 24 hours and again at 60 days. All tested materials showed different hardness values, and the values of top surfaces of the specimens were found to be higher than the bottom surface in all test groups. There was no statistical difference in the Vickers hardness (HV) values when the test specimens were kept in water storage. In conclusion Hytac displayed microhardness values higher than Vitremer and Dyract. We found the order of HV values to be Surfil > Hytac > Dyract > Vitremer, respectively. Vitremer presented the lowest microhardness level and Surfil the highest.

PMID: 15558089 [PubMed - indexed for MEDLINE]

Wear and mechanical properties of nano-silica-fused whisker composites.

J Dent Res. 2004 Dec;83(12):930-5

Authors: Xu HH, Quinn JB, Giuseppetti AA

Resin composites must be improved if they are to overcome the high failure rates in large stress-bearing posterior restorations. This study aimed to improve wear resistance via nano-silica-fused whiskers. It was hypothesized that nano-silica-fused whiskers would significantly improve composite mechanical properties and wear resistance. Nano-silicas were fused onto whiskers and incorporated into a resin at mass fractions of 0%-74%. Fracture toughness (mean +/- SD; n = 6) was 2.92 +/- 0.14 MPa.m(1/2) for whisker composite with 74% fillers, higher than 1.13 +/- 0.19 MPa.m(1/2) for a prosthetic control, and 0.95 +/- 0.11 MPa.m(1/2) for an inlay/onlay control (Tukey's at 0.95). A whisker composite with 74% fillers had a wear depth of 77.7 +/- 6.9 mum, less than 118.0 +/- 23.8 microm of an inlay/onlay control, and 172.5 +/- 15.4 microm of a prosthetic control (p < 0.05). Linear correlations were established between wear and hardness, modulus, strength, and toughness, with R = 0.95-0.97. Novel nano-silica-fused whisker composites possessed high toughness and wear resistance with smooth worn surfaces, and may be useful in large stress-bearing restorations.

PMID: 15557400 [PubMed - indexed for MEDLINE]

A 12 month clinical study of bond failures of recycled versus new stainless steel orthodontic brackets.

Eur J Orthod. 2004 Aug;26(4):449-54

Authors: Cacciafesta V, Sfondrini MF, Melsen B, Scribante A

The purpose of this prospective longitudinal randomized study was to compare the clinical performance of recycled brackets with that of new stainless steel brackets (Orthos). Twenty patients treated with fixed appliances were included in the investigation. Using a 'split-mouth' design, the dentition of each patient was divided into four quadrants. In 11 randomly selected patients, the maxillary left and mandibular right quadrants were bonded with recycled brackets, and the remaining quadrants with new stainless steel brackets. In the other nine patients the quadrants were inverted. Three hundred and ten stainless steel brackets were examined: 156 were recycled and the remaining 154 were new. All the brackets were bonded with a self-cured resin-modified glass ionomer (GC Fuji Ortho). The number, cause, and date of bracket failures were recorded over 12 months. Statistical analysis was performed by means of a paired t-test, Kaplan-Meier survival estimates, and the log-rank test. No statistically significant differences were found between: (a) the total bond failure rate of recycled and new stainless steel brackets; (b) the upper and lower arches; (c) the anterior and posterior segments. These findings demonstrate that recycling metallic orthodontic brackets can be of benefit to the profession, both economically and ecologically, as long as the orthodontist is aware of the various aspects of the recycling methods, and that patients are informed about the type of bracket that will be used for their treatment.

PMID: 15366391 [PubMed - indexed for MEDLINE]

Water-dependent interfacial transition zone in resin-modified glass-ionomer cement/dentin interfaces.

J Dent Res. 2004 Aug;83(8):644-9

Authors: Tay FR, Sidhu SK, Watson TF, Pashley DH

The function of the interfacial transition zone (absorption layer) in resin-modified glass-ionomer cements bonded to deep dentin remains obscure. This study tested the hypotheses that the absorption layer is formed only in the presence of water derived from hydrated dentin and allows for better bonding of resin-modified glass-ionomer cements to dentin. Ten percent polyacrylic acid-conditioned, hydrated, and dehydrated deep dentin specimens were bonded with 2 resin-modified glass-ionomer cements and sealed with resins to prevent environmental water gain or loss. A non-particulate absorption layer was identified over hydrated dentin only, and was clearly discernible from the hybrid layer when bonded interfaces were examined with transmission electron microscopy. This layer was relatively more resistant to dehydration stresses, and remained intact over the dentin surface after tensile testing. The absorption layer mediates better bonding of resin-modified glass-ionomer cements to deep dentin, and functions as a stress-relieving layer to reduce stresses induced by desiccation and shrinkage.

PMID: 15271975 [PubMed - indexed for MEDLINE]

In vitro inhibition of caries-like lesions with fluoride-releasing materials.

J Oral Sci. 2004 Mar;46(1):45-50

Authors: Yaman SD, Er O, Yetmez M, Karabay GA

The aim of this study was to compare the in vitro caries inhibition of various resin-based materials. Class V cavities were prepared in twenty-five freshly extracted human premolar teeth which were then restored with glass-ionomer cement (Chemfill II), compomer (Compoglass F, Dyract AP) and composite resin (Tetric Ceram and Z 100). The teeth were submerged in an acid gel for 6 weeks. Each specimen was sectioned. These sections were left in water for 24 hours, and then examined using polarized light microscopy. The lesion consisted of two parts, the outer surface lesion and the cavity wall lesion. There was no significant difference in the body depth of the outer lesion and in the depth of the wall lesion among teeth restored with Compoglass F, Dyract AP and Chemfill II (P > 0.05). There was a significant difference between those restored with Z 100 and Tetric Ceram (P < 0.05). The length of the wall lesion for the teeth restored with Chemfill II was significantly smaller than that in the remaining groups (P < 0.05). The length of the wall lesion for teeth restored with Tetric Ceram and Z 100 was significantly higher than in the remaining groups (P < 0.05). These results suggest that composite materials and compomer provide less caries inhibition than glass-ionomer cements.

PMID: 15141723 [PubMed - indexed for MEDLINE]

A clinical study of glass ionomer cement.

Eur J Orthod. 2004 Apr;26(2):185-9

Authors: Oliveira SR, Rosenbach G, Brunhard IH, Almeida MA, Chevitarese O

The aim of this investigation was to compare the clinical performance of a glass ionomer cement (GIC) with a composite resin when used for direct bonding of standard edgewise orthodontic brackets. Fourteen patients (10 females, four males), in whom 242 teeth were bonded with brackets, were divided into two groups: GIC (121 teeth) and composite (121 teeth). The brackets were allocated to alternate quadrants and first-time failures were recorded over a period of 24 months. Data were analysed statistically (non-parametric chi-squared test). The results demonstrated a significantly lower unpreviewed debonding index (UDI) (15.7 per cent) for the composite than for the GIC (28.1 per cent) (P = 0.042). The use of heavy archwires was largely responsible for this difference. No difference was observed when light and medium archwires were used. GIC may be a viable alternative to composite for use with light archwires and with limited treatment objectives.

PMID: 15130042 [PubMed - indexed for MEDLINE]

A three-year clinical evaluation of two dentin bonding agents.

J Am Dent Assoc. 2004 Apr;135(4):451-7

Authors: Matis BA, Cochran MJ, Carlson TJ, Guba C, Eckert GJ

BACKGROUND: A new restorative called a "giomer composite" has been introduced. The authors conducted a study to determine retention, anatomical form, caries, staining, marginal discoloration, marginal adaptation, surface roughness and sensitivity of giomer compared with those of a microfilled composite. METHODS: The authors placed 40 sets of restorations randomly in canines and premolars in vivo. They used a giomer composite and a microfilled composite in erosion/abrasion/abfraction Class V lesions that were not altered with rotary instruments. They placed the restorations according to manufacturer's recommendations, and two calibrated examiners evaluated the restorations independently using modified U.S. Public Health Service criteria at baseline and at six, 18 and 36 months. The lesions receiving the restorations did not differ from each other in the amount of circumferential enamel present, the percentage of the surface area of dentin or lesion type. RESULTS: There were no differences in the restorations at baseline, an evaluation made two weeks after placement. At 36 months, the giomer and microfilled composite restorations were not significantly different from one another in any of the eight criteria evaluated. The percentage agreement between examiners was at least 83 percent for each criterion in each evaluation period. CONCLUSIONS: Both the giomer and the microfilled composite used in this study meet the clinical portion of the Acceptance Program Guidelines for Dentin and Enamel Adhesives Materials established by the American Dental Association. CLINICAL IMPLICATIONS: Both the giomer and the microfilled composite used in this study can be used with confidence in Class V lesions.

PMID: 15127867 [PubMed - indexed for MEDLINE]